background image

WT5HP/WTE5HP/WT5HPSG WATER TRAILERS • OPERATION  MANUAL — REV. #1 (03/14/17) — PAGE 7

SAFETY INFORMATION

PUMP SAFETY

  DANGER

 

„

NEVER

 operate the equipment in an explosive 

atmosphere or near combustible materials. An 

explosion or fi re could result causing severe 

bodily harm or even death.

  WARNING

 

 

„

Accidental starting can cause severe injury 

or death.

 ALWAYS

 place the ON/OFF 

switch in the OFF position.

 

„

DO NOT

 place hands or fingers inside 

pump when pump is running.

 

„

NEVER

 disconnect any 

emergency or 

safety devices.

 

These devices are intended for operator 

safety. Disconnection of these devices can cause severe 

injury, bodily harm or even death. Disconnection of any 

of these devices will void all warranties.

  CAUTION

 

„

Be careful of discharge whipping under pressure.

  NOTICE

 

„

NEVER

 leave an open pump chamber unattended.

 

„

ALWAYS

 keep the machine in proper running condition.

 

„

DO NOT

 attempt to thaw-out a frozen pump by using 

a torch or other source of fl ame. Application of heat in 

this manner may heat the oil in the seal cavity above the 

critical point, causing pump damage.

 

„

DO NOT

 pump water greater than 140° F. 

 

„

DO NOT

 pump liquids containing acid or alkali.

 

„

DO NOT

 fi ll/pump heavy debris laden water.

 

„

Fix damage to machine and replace any broken parts 

immediately.

 

„

ALWAYS

 store equipment properly when it is not being 

used. Equipment should be stored in a clean, dry location 

out of the reach of children and unauthorized personnel.

 

„

NEVER

 lubricate components or attempt service on a 

running machine.

 

„

ALWAYS

 allow the machine a proper amount of time to 

cool before servicing.

 

„

Keep machine in proper running condition.

ENGINE SAFETY

  WARNING

 

„

DO NOT 

place hands or fingers inside engine 

compartment when engine is running.

 

„

NEVER

 operate the engine with heat shields or 

guards removed.

 

„

DO NOT

 remove the engine oil drain plug 

while the engine is hot. Hot oil will gush 

out of the oil tank and severely scald any 

persons in the general area of the pump.

  CAUTION

 

„

NEVER

 touch the hot exhaust manifold, 

muffl er or cylinder. Allow these parts to cool 

before servicing equipment.

  NOTICE

 

„

NEVER

 run engine without an air fi lter or with a dirty air 

fi lter. Severe engine damage may occur. Service air fi lter 

frequently to prevent engine malfunction.

 

„

NEVER

 tamper with the factory settings 

of the engine or engine governor. Damage 

to the engine or equipment can result 

if operating in speed ranges above the 

maximum allowable.

Discount-Equipment.com

Содержание WT5HP























































Отзывы: