MULTIQUIP WhisperWatt DCA300SSC Скачать руководство пользователя страница 20

Страница: 20 / 104

page 20 — DCa300SSC / DCa300SSCU gen. • operation anD partS manUal — rev. #1 (08/10/11)

engine Operating paneL

The definitions below describe the controls and functions

of the Engine Operating Panel (Figure 5).
1.

Tachometer

— Indicates engine speed in RPM’s for 60

Hz operation. This meter should indicate 1800 RPM’s

when the rated load is applied. In addition a built in hour

meter will record the number of operational hours that

the generator has been in use.

oil pressure gauge

— During normal operation this

gauge be should read between 28 to 85 psi. (193~586

kPa). When starting the generator the oil pressure may

read a little higher, but after the engine warms up the oil

pressure should return to the correct pressure range.

Water temperature gauge

— During normal operation

this gauge be should read between 167° and 203°F

(75°~95°C).

Charging Ammeter Gauge

— Indicates the current

being supplied by the engine’s alternator which

provides current for generator’s control circuits and

battery charging system.

Fuel Gauge

— Indicates amount of diesel fuel available.

engine Warning lamps

— There are three engine

warning lamps, they are defined as follows:
a.

overheat lamp

— This lamp goes

when the cooling water temperature rises

abnormally. If the lamp goes

during

normal operation of the generator, the

emergency shutdown device will stop the

engine automatically.

low oil pressure lamp

— During

normal operation of the generator this

lamp should remain

oFF

. When the

auto-oFF/reset-manual

switch is set

to the

manUal

position to start the engine, the

lamp will be lit. When the oil pressure rises after

start-up the lamp will go OFF. If this lamp is ever

lit (

) during normal operation of the generator,

the emergency shutdown device will stop the engine

automatically.

low Fuel level lamp

— When this lamp

is ON, it is time to stop the engine and

add fuel. Remember to let the engine cool

before adding fuel (DCA300SSC only).

Air Filter Alarm

— When the air filter

element is clogged, this lamp goes

indicating the element should be

immediately cleaned or replaced.

Coolant level alarm

— This lamp

goes

when the coolant level is low.

If this lamp goes

while the engine is

in operation, the emergency shutdown

device will automatically stop the engine.

Engine Speed Switch

— This switch controls the

speed of the engine (low/high).

pre-Heat lamp

— When ECU is placed in

aUx

position, pre-heat lamp will be

. When pre-heat

cycle is completed, lamp will turn

oFF

emergency Stop Button

— Push this button inward to

stop the engine in the event of an emergency.

Do not

use this button as a means of stopping the engine.

10.

Battery Switch

— This switch should be set to the

position during normal operation. When the engine has

been stop, place this switch in the

oFF

position.

not

turn this switch during normal operation, it could

cause damage to the electrical equipment.

Figure 5. Engine Operating Panel

OFF

OIL PRESS.

FUEL LEVEL

WATER TEMP.

AIR FILTER

COOLANT LEVEL

Содержание WhisperWatt DCA300SSC









































































































Результаты поиска

Содержание WhisperWatt DCA300SSC

Отзывы:

Бренды по названию

Популярные бренды

MULTIQUIP WhisperWatt DCA300SSC, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание WhisperWatt DCA300SSC

Отзывы:

Бренды по названию

Популярные бренды