MULTIQUIP WhisperWatt DCA300SSC Скачать руководство пользователя страница 19

Страница: 19 / 104

DCa300SSC / DCa300SSCU gen. • operation anD partS manUal — rev. #1 (08/10/11) — page 19

generatOr cOntrOL paneL

mpeC Control Switch

— This switch controls the

running of the unit. If this switch is set to the

oFF/reSet

position, the unit will not run. When this switch is set to the

manual position, the generator will start immediately.

If the generator is to be connected to a building’s AC

power source via a transfer switch (isolation), place the

switch in the AUTO position. In this position, should an

outage occur, the automatic transfer switch (ATS) will

start the generator automatically via the generator’s auto-

start contacts conn ected to the ATS’s start contacts.

Please refer to your ATS installation manual for further

instructions for the correct installation of the auto-start

contacts of the geerator to the ATS.

low oil pressure

— Indicates the engine pressure

has fallen below a safe operating level. The oil pressure

is detected using variable resistive values from the

oil pressure sending unit. This is considered a

major

fault.

High Coolant Temperature

— Indicates the engine

temperature has exceeded a safe operating level. The

engine temperature is detected using variable resistive

values from the temperature sending unit. This is

considered a

major

fault.

overcrank Shutdown

— Indicates the unit has

attempted to start a pre- programmed number of

timesand has failed to start. The number of cycles and

duration are programmable. It is pre-set at 3 cycles with

a 10-second duration. This is considered a

major

fault.

overspeed Shutdown

— Indicates the engine is running

at an unsafe speed. This is considered a

major

fault.

engine running

— Indicates that engine is running at

a safe operating speed.

Located behind the generator control panel is the

generator Control Box

. This box contains some of the

necessary electronic components required to make the

generator function.

The

Control Box

is equipped with the following major

components:

Over-Current Relay

Voltage Rectifier (AVR)

Starter Relay

Current Transformer

Voltage Change-Over Board

Three Phase Circuit Breaker

NOTICE

Remember the

overcurrent relay

monitors the current

flowing from the

U,v, and W output terminal lugs

to the load.
In the event of a short circuit or over current condition,

it will automatically trip the 800 amp main breaker.
To restore power to the

output terminal panel

, press

the reset button on the overcurrent relay and place the

main

circuit breaker in the

closed

position (

Содержание WhisperWatt DCA300SSC









































































































Результаты поиска

Содержание WhisperWatt DCA300SSC

Отзывы:

Бренды по названию

Популярные бренды

MULTIQUIP WhisperWatt DCA300SSC, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание WhisperWatt DCA300SSC

Отзывы:

Бренды по названию

Популярные бренды