MULTIQUIP MQP20P страница 23 Скачать руководство пользователя

Страница: 23 / 80

MQp20p STaNDBY geNeRaTOR • OpeRaTiON aND paRTS MaNual — Rev. #1 (11/28/11) — page 23

InSPECtIOn/SEtuP

MaiN CiRCuiT BReakeR

The generator is equipped with a 3-pole, 100-amp circuit

breaker to protect it from overload. Make sure that the circuit

breaker is in the OFF position prior to starting the engine.

luBRiCaTiON Oil

Fill the engine crankcase with lubricating oil through the

filler hole, but

DO NOT

overfill. Make sure the generator

is level and verify that the oil level is maintained between

the two notches (Figure 7) on the dipstick. See Table 9 for

proper selection of engine oil.

Figure 7. Engine Oil Dipstick

When checking the engine oil, be sure to check if the oil is

clean. If the oil is not clean, drain the oil by removing the

oil drain plug, and refill with the specified amount of oil as

outlined in the

perkins engine Owner’s Manual

. Oil should

be warm before draining.
Other types of motor oils may be substituted if they meet

the following requirements:

API Service Classification CC/SC

API Service Classification CC/SD

API Service Classification CC/SE

API Service Classification CC/SF

Table 9. Recommended Motor Oil

Fuel CHeCk

Refilling the Fuel System

This generator has a fuel tank located in the sub base

assembly frame (Figure 3).

alWaYS

fill the fuel tank with

clean fresh

#2 diesel fuel. DO NOT

fill the fuel tank beyond

its capacity.
Pay attention to the fuel tank capacity when replenishing

fuel. The fuel tank cap must be closed tightly after filling.

Handle fuel in a safe container. If the container does

not have a spout, use a funnel. Wipe up any spilled fuel

immediately.

Refueling procedure:

DaNgeR

Fuel spillage on a

hot

engine can cause

fire

explosion

. If fuel spillage occurs,

wipe up the spilled fuel completely to

prevent fire hazards.

NeveR

smoke

around or near the generator.

CauTiON

ONlY properly trained personnel

who have read

and understood this section should refill the fuel tank

system.

WaRNiNg

Diesel fuel

and its vapors are dangerous

to your health and the surrounding

environment. Avoid skin contact and/or

inhaling fumes.

CauTiON

alWaYS

make sure generator is on firm level ground

before refueling to prevent spilling and maximize the

amount of fuel that can be pumped into the tank.

Содержание MQP20P

















































































Результаты поиска

Содержание MQP20P

Отзывы:

Похожие инструкции для MQP20P

Бренды по названию

Популярные бренды

MULTIQUIP MQP20P, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MQP20P

Отзывы:

Похожие инструкции для MQP20P

Бренды по названию

Популярные бренды