MULTIQUIP MQP20P страница 26 Скачать руководство пользователя

Страница: 26 / 80

page 26 —MQp20p STaNDBY geNeRaTOR • OpeRaTiON aND paRTS MaNual — Rev. #1 (11/28/11)

InSPECtIOn/SEtuP

Battery Cable installation

alWaYS

make sure that the battery cables (Figure 13) are

properly connected to the battery terminals as shown below.

Figure 13. Battery Connections

When connecting the battery do the following:
1. Place a small amount of battery terminal treatment

compound around both battery terminals. This will

ensure a good connection and will help prevent

corrosion around the battery terminals.

2. Connect the

red cable

to the positive terminal of the

battery and the

black cable

to the negative terminal

of the battery.

CauTiON

alWaYS

disconnect the negative terminal

FiRST

and

reconnect negative terminal

laST

NOTICE

If the battery cable is connected incorrectly, electrical

damage to the generator will occur. Pay close attention

to the polarity when connecting the battery.

CauTiON

Inadequate battery connections may cause poor

starting of the generator, and create other malfunctions.

alTeRNaTOR

The polarity of the alternator is negative grounding type.

When an inverted circuit connection takes place, the circuit

will short instantaneously resulting in alternator failure.

DO NOT

put water directly on the alternator. Water in the

alternator can cause corrosion and damage.

WiRiNg

Inspect the generator for bad, worn electrical wiring or

connections. If any wiring or connections are exposed

(insulation missing), replace wiring immediately.

pipiNg aND HOSe CONNeCTiON

Inspect all piping, oil hose, and fuel hose connections for

wear and tightness. Tighten all hose clamps and check

hoses for leaks.
If any hose (

fuel or oil

) lines are defective, replace them

immediately.

Содержание MQP20P

















































































Результаты поиска

Содержание MQP20P

Отзывы:

Похожие инструкции для MQP20P

Бренды по названию

Популярные бренды

MULTIQUIP MQP20P, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MQP20P

Отзывы:

Похожие инструкции для MQP20P

Бренды по названию

Популярные бренды