MULTIQUIP EM120 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 58

background image

EM120 HYD. PLASTER/MORTAR MIXER• OPERATION AND PARTS MANUAL — REV. #1 (09/09/19) — PAGE 33

MIXER STORAGE

For storage of the mixer for over 30 days, the following is

recommended:

Drain the fuel tank completely, or add STA-BIL to the fuel.

Run the engine until the fuel is completely consumed.

Completely drain used oil from the engine crankcase

and fill with fresh clean oil, then follow the procedures

described in the engine manual for engine storage.

Clean the entire mixer and engine compartment.

Place the mixing drum in the down position (mouth facing

downward).

Cover the mixer and place it a clean dry area, that is

protected from harsh elements.

MAINTENANCE (MIXER)

«
...
31
32
33
34
35
...
»

Содержание EM120



























































Отзывы:

Нет отзывов

Похожие инструкции для EM120

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: York Fitness Страницы: 34

Бренд: K-SPORT Страницы: 5

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: VaBroom Страницы: 4

Бренд: v.link Страницы: 20

Бренд: BCP Страницы: 8

Бренд: Coba Страницы: 2

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

home FLP 1600 SOLAR

Бренд: Somogyi Elektronic Страницы: 15

GSE electronic ballast

Бренд: G-Systems Страницы: 38

AeroX Audio 105

Бренд: Campbell Страницы: 23

Бренд: ACS Страницы: 23

Бренд: Casall Страницы: 18

Бренд: Autogram Страницы: 31

BTL6-V1 E-M Series

Бренд: Balluff Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды