MULTIQUIP EM120 Скачать руководство пользователя страница 14

Страница: 14 / 58

PAGE 14 — EM120 HYD. PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/09/19)

GENERAL INFORMATION

APPLICATION

This mixer is

only

intended for the mixing of

plaster

and

mortar

. The mixer must be used for its intended purpose

and is not suitable for the mixing of

flammable

explosive

substances. The mixer

must not be used

in an explosive

atmosphere.
The drum capacity of this hydraulic mixer is 12.0 cu. ft.

(340 liters) with a batch capacity between 3-1/2 and 4-1/2

bags. Mixer is shipped completely assembled and has been

factory tested and is ready for use.

POWER PLANTS

Mixer is powered by a 11.7 HP, air-cooled, 4-stroke gasoline

engine. Refer to Table 2 for specific engine details.

HARDWARE

Check all hardware on the mixer before starting. Periodically

inspect all hardware. Loose hardware can contribute

to early component failure and poor performance. Use

Table 4 as general guideline when the torqueing of mixer

hardware is required. Remember to keep all mixer hardware

components tight.

Table 4. Hardware Torque Recommendations

Hardware Diameter

Torque (ft-lbs)

5/16-inch x 18

3/8-inch x 16

3/8-inch x 24

1/2-inch x 13

1/2-inch x 13 (Grade 8)

ENGINE MAINTENANCE

For basic engine maintenance, refer to the engine

maintenance section in this manual. For more detailed

engine maintenance, refer to the Honda Engine Owner's
manual furnished with the engine.

Содержание EM120



























































Результаты поиска

Содержание EM120

Отзывы:

Похожие инструкции для EM120

Бренды по названию

Популярные бренды

MULTIQUIP EM120, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание EM120

Отзывы:

Похожие инструкции для EM120

Бренды по названию

Популярные бренды