background image

PAGE 8 — BPX GASOLINE VIBRATOR • OPERATION AND PARTS MANUAL — REV. #1 (08/28/17) 

SAFETY INFORMATION

 

„

NEVER lubricate components or attempt service on a

running machine.

 

„

ALWAYS allow the vibrator a proper amount of time to

cool before servicing.

NOTICE

 

„

ALWAYS keep the machine in proper running condition.

 

„

ALWAYS become familiar with the components of the

vibrator before operating.

 

„

Fix damage to machine and replace any broken parts

immediately.

 

„

ALWAYS store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children and unauthorized personnel.

ENGINE SAFETY

  DANGER

 

„

The engine fuel exhaust gases contain poisonous carbon 

monoxide. This gas is colorless and odorless, and can

cause death if inhaled.

 

„

The engine of this equipment 

requires an adequate free

fl ow of cooling air. 

NEVER

operate this equipment in

any enclosed or narrow area

where free fl ow of the air is

restricted. If the air fl ow is

restricted it will cause injury to people and property and

serious damage to the equipment or engine. Remember

the engine gives off 

DEADLY gases.

 WARNING

 

„

NEVER operate the engine with heat shields or

guards removed.

 

„

DO NOT remove the engine oil drain plug while

the engine is hot. Hot oil will gush out of the engine

crankcase and severely scald any persons in the general 

area of the vibrator.

  CAUTION

 

„

NEVER touch the hot exhaust manifold,

muffl er or cylinder. Allow these parts to cool

before servicing equipment.

 

„

ALWAYS place the engine ON/OFF switch in the OFF

position when the vibrator is not in use.

 

„

NEVER tamper with the factory settings

of the engine or engine governor. Damage

to the engine or equipment can result

if operating in speed ranges above the

maximum allowable.

NOTICE

 

„

Refer to the 

Engine Owner's Manual

 for engine 

technical questions or information.

 

„

NEVER run engine without an air fi lter or with a dirty air 

fi lter. Severe engine damage may occur. Service air fi lter

frequently to prevent engine malfunction.

 

„

State Health Safety Codes and Public Resources

Codes specify that in certain locations, spark arresters 

must be used on internal combustion engines that use 

hydrocarbon fuels. A spark arrester is a device designed 

to prevent accidental discharge of sparks or fl ames 

from the engine exhaust. Spark arresters are qualifi ed 

and rated by the United States Forest Service for this 

purpose. In order to comply with local laws regarding 

spark arresters, consult the engine distributor or the 

local Health and Safety Administrator.

FUEL SAFETY

  DANGER

 

„

DO NOT add fuel to equipment if it is placed inside truck 

bed with plastic liner. Possibility exists of explosion or fi re

due to static electricity.

 

„

DO NOT start the engine near spilled fuel or combustible

fl uids. Gasoline fuel is extremely fl ammable and its

vapors can cause an explosion if ignited.

 

„

ALWAYS refuel in a well-ventilated area, away from 

sparks and open fl ames.

 

„

ALWAYS use extreme caution when working with

fl ammable liquids.

 

„

DO NOT fi ll the fuel tank while the engine is running 

or hot.

 

„

DO NOT overfi ll tank, since spilled fuel could ignite if it 

comes into contact with hot engine parts or sparks from 

the ignition system.

Discount-Equipment.com

Содержание BPX













































Отзывы: