MULTIQUIP BPX страница 16 Скачать руководство пользователя

Страница: 16 / 44

PAGE 16 — BPX GASOLINE VIBRATOR • OPERATION AND PARTS MANUAL — REV. #1 (08/28/17)

Head and Shaft Connections

Before operating the BPX, follow the instructions below

to connect the flexible shaft, vibrator head, and vibrator.

Connecting the Flexible Shaft and Vibrator Head

Perform the following procedure to attach the FS series or

FSN series flexible shaft to the vibrator and vibrator head.

Refer to Figure 4.
12. Pull up on the Quick Disconnect (Q.D.) locking knob

and insert the Q.D. coupler into the eccentric end bell

assembly.

13. Attach the vibrating head to the other end of the flexible

shaft. The use of a small amount of pipe thread sealant

(Red Loctite

271™) is recommended on the flexible

shaft casing coupling threads to prevent water from

entering the vibrator head.

CAUTION

Before initial use, dissassemble the Quick Disconnect

coupler at the end of the flexible shaft. Check the shaft

for grease and reassemble the coupler, making sure to

apply Loctite

242™ thread sealant to the male threads

of the coupler.
Failure to follow these instructions may result in

equipment damage and/or bodily injury.

NOTICE

The shafts are shipped from the factory pre-greased

and require no greasing at this time. Refer to the

Maintenance

section of this manual for shaft greasing

requirements.

NOTICE

The QD coupler and spindle shaft for the FS and FSN

Series are included with the flexible shaft.

SET-UP

Applying Loctite

When applying Red Loctite

271™ to the flexible shaft

casing threads:
1. Clean the mating connector or coupler threads with

Loctite

Primer™.

2. Allow the primer to dry for several minutes before

applying a ring of Red Loctite

271™ to the middle of

the flexible shaft casing threads.

3. Screw the head tightly onto the flexible shaft casing and

wait one hour before use. The threads are left-handed;

turn

counterclockwise to tighten. An equivalent brand

of anaerobic sealant may be used.

DISASSEMBLY

1. Remove the motor from the shaft.
2. Remove the core from the shaft housing. The head

does not need to be removed unless it also requires

servicing.

3. As the core is removed, slide it through a clean shop

cloth to wipe off old grease. Keep it clean and off the

ground or floor.

4. After inspecting the core for obvious damage,

place a handful of clean grease (Shell Durina EP2

high- temperature, high-pressure grease or equivalent)

in a shop cloth and slide the clean core through the

grease as you feed the core back into the shaft housing.

This will lightly coat the core.

DO NOT overgrease. As

the square end of the core approaches the head, turn

the core slightly to engage the drive adaptor inside

the head while continuing to push it towards the head.

5. Install the motor onto the shaft assembly and securely

tighten the nut.

6. Test run the motor and check head vibration.

DO NOT

run the vibrator in the air (not in concrete mix) for longer

than 1–2 minutes.

CAUTION

Wear protective leather gloves while disassembling

the vibrator.

Discount-Equipment.com

Содержание BPX













































Результаты поиска

Содержание BPX

Отзывы:

Похожие инструкции для BPX

Бренды по названию

Популярные бренды

MULTIQUIP BPX, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание BPX

Отзывы:

Похожие инструкции для BPX

Бренды по названию

Популярные бренды