MULTIQUIP B46H11 Скачать руководство пользователя страница 23

Страница: 23 / 50

J36/B46-M30 SERIES WALK-BEHIND TROWELS • OPERATION MANUAL — REV. #1 (11/17/17) — PAGE 23

Centrifugal Safety Stop Switch Connection

Connect the black tail wire from the engine to the black

safety stop wire from the centrifugal stop switch as shown

in Figure 10.

Figure 10. Centrifugal Safety Stop Switch

Connection

Blade Pitch Cable Installation

1. For trowels equipped with a

standard

handle (SXHC),

turn the star wheel

counterclockwise to release

tension on the blade pitch cable. See Figure 11.

Figure 11. Blade Pitch Cable Adjustment

(Standard Handle)

2. For trowels equipped with a

Quick Pitch™ handle

(QXHC), squeeze the trigger lock and push the

T-handle towards the engine to release tension on the

blade pitch cable. See Figure 12.

SAFETY STOP WIRE

CONNECTION POINT

INCREASE

BLADE PITCH

(CW)

DECREASE

BLADE PITCH

(CCW)

Figure 12. Blade Pitch Cable Adjustment

(Quick Pitch™ Handle)

3. Remove brass set nut #1 from the end of the blade

pitch cable (Figure 13).

Figure 13. Blade Pitch Cable

4. Thread brass set nut #2 as far as possible towards the

blade pitch cable (Figure 13).

T-HANDLE

TRIGGER

LOCK

PITCH

FULL

PITCH

WARNING

The Quick Pitch™ T-handle is under spring tension and

can snap in the direction of force (toward the user) if not

firmly grasped, which may cause bodily injury.

BLADE

PITCH

CABLE

BRASS SET

NUT #1

BRASS SET

NUT #2

SET-UP

Содержание B46H11



















































Результаты поиска

Содержание B46H11

Отзывы:

Похожие инструкции для B46H11

Бренды по названию

Популярные бренды

MULTIQUIP B46H11, Руководство по эксплуатации

Результаты поиска

Содержание B46H11

Отзывы:

Похожие инструкции для B46H11

Бренды по названию

Популярные бренды