MULTIQUIP B46H11 Скачать руководство пользователя страница 21

Страница: 21 / 50

J36/B46-M30 SERIES WALK-BEHIND TROWELS • OPERATION MANUAL — REV. #1 (11/17/17) — PAGE 21

SET-UP

UNPACKING THE HANDLE

The handle (Figure 4) is shipped in the folded, or stowed,

position.
1. To place the folding upper handle in the operational

position, turn the star wheel

counterclockwise to

release it from its folded/stowed position.

2. Pull back on the upper handle to place the handle in

the operational position. Turn the star wheel

clockwise

to secure the handle firmly in place.

Figure 4. Unpacking the Handle

FOLDED

POSITION

OPERATIONAL

POSITION

STAR

WHEEL

UPPER

HANDLE

OPERATIONAL

POSITION

ASSEMBLY AND INSTALLATION

Some components must be installed before the trowel can

be operated. This section provides general instructions

on how to install these components.

For more detailed

handle

assembly intructions, contact Multiquip and

request Instruction Sheet P/N 20485.

Handle Tube Installation

Attach the main handle (tube) to the gearbox using the

supplied hardware as shown in Figure 5.

Figure 5. Handle Tube Installation

Vibratory Handlebar Adjustment

The vibratory handlebar is already attached to the main

handle tube.
To adjust the height of the

handlebar

, loosen the star wheel

(Figure 6), and move the

handlebar

to the desired position.

Tighten the star wheel firmly to secure.

Figure 6. T-Handle Bar Adjustment

GEARBOX

3/8 FLAT

WASHER

3/8-16 X 3.25

HHC SCREW

MAIN HANDLE

(TUBE)

3/8-16

NYLOC NUT

HANDLEBAR

HEIGHT

ADJUSTMENT

STAR WHEEL

Содержание B46H11



















































Результаты поиска

Содержание B46H11

Отзывы:

Похожие инструкции для B46H11

Бренды по названию

Популярные бренды

MULTIQUIP B46H11, Руководство по эксплуатации

Результаты поиска

Содержание B46H11

Отзывы:

Похожие инструкции для B46H11

Бренды по названию

Популярные бренды