Multiple Awnings Multiple Shade Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 26

Multiple Awnings Multiple Shade Скачать руководство пользователя страница 20

Multiple Awnings inc. – 1505A rue de l’Industrie, Beloeil QC, J3G 0S5 CANADA

20

Multiple Shade V01.3 04 2019

8. Appendices

8.A.

Motor and remote resetting and synchronisation

Note:

This procedure describes the steps necessary to restore communication between the

motor  and  the  remote  handset  unit  supplied  with  your  motorized  Multiple  Shade.  This
procedure  must  be  performed  only  if  the  remote  handset  does  not  operate  the  motorized
Multiple  Shade.  Review  the  steps  below  to  familiarize  yourself  with  the  procedure  before
attempting to complete it. PLEASE ALSO NOTE THAT THE TIME BETWEEN 2 OPERATIONS HAS
TO  BE  SHORTER  THAN  4  SECONDS  OTHERWISE  YOU  WILL  NEED  TO  RE-START  THE  PROCESS
COMPLETELY FROM THE BEGINNING. Also make sure to select and note the remote channel
you will be using.

01.   Make sure that the red LED (previously set to the channel you will be using) on the front of the
         remote handset is lighting up when you are pressing an holding a button. If the red LED does
         not light up at all or flashes for less than 5 seconds, you will need to replace the battery (see
         section 7.2).
02.   Disconnect the power cord (120V AC) for 10 seconds.
03.   Reconnect the power cord the motor will beep 3 times.
04.   Press and hold the motor setting button located underneath the solar shade on the motor
         side (see figures 13 and 14) until the motor emits 1 beep and jogs 2 times.
05.   Use a paper clip or pencil and press the P2 button (see figure 12) the motor will again
         emit a beep and jog twice. Press the P2 button once more and the motor will emit another
         beep and jog twice again.
06.   Press the UP (close) button 1 time, the motor will emit 3 beeps and jog twice. Verify that the
         motor runs correctly in the appropriate directions . If the direction of the buttons are reversed,
         see section 8.C. to change the directions.

Figure 11

Figure 12

Figure 13

Figure 14

«
...
18
19
20
21
22
...
»

Содержание Multiple Shade



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды