MULTILIFT XR S Скачать руководство пользователя страница 61

Страница: 61 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

CXXX

dXXX

Lowering the tipping device

12.

Lower the tipping arm (middle

frame together with the rear frame)

- move the control lever forward

- stop the movement by releasing the

control lever.

12.

Lower the tipping arm (middle

frame together with the rear

frame

)

- move the control lever forward

- stop the movement by releasing

the control lever.

The main cylinders are released (floating) when the flatrack/body is about 60 mm

above the body supports, and the final stage of unloading is dampened.

13.

Check that the frame of the XR21S equipment and the flatrack/body are in the

lowest position.

14.

Close the flatrack/body tail gate.

15.

Shut off the oil supply of the hydraulic pump.

16.

Check that all signal lights of the control unit have gone out.

MANUAL MODE A5

AUTOMATIC MODE A2

Safety codes

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды