MultiDyne SilverBack V Скачать руководство пользователя страница 29

Страница: 29 / 64

SilverBack V Camera-Mountable Fiber Optic Transmission System

Made in the USA

Page

Viewfinder Configuration and Operation

On certain SilverBack V camera unit models, some of the secondary SDI connections can be re-assigned

in the Settings menu to connect to a built-in internal viewfinder switch. The camera unit configurations

that support a built-in viewfinder switch are shown in the table below.

Configuration

C3EO

C3GX

C2X2

C4K1

C4K2

C42R

C44R

C3X3

Viewfinder Switch

YES

Three types of 3G-SDI cards can be installed in internal card slots: 2Tx, 2Rx, and TRx. Typically, a VF-

capable card is installed in the slot closest to the Ethernet or audio connectors.

The viewfinder is configured from the Viewfinder Setup menu under Video Settings.

MENU > Video Settings > Viewfinder >

•

Enable: On or Off (default)

•

Card Slot: 1-4 (available slots depend on the number and type of SDI cards installed)

The Camera Viewfinder may also be configured remotely, from the webpage dashboard accessed from

the Base Unit.

Audio Settings

SilverBack V camera unit audio input and output are configured in the Audio Settings menu.

MENU > Audio Settings

•

Input

•

Output

•

Intercom

Содержание SilverBack V

































































Результаты поиска

Содержание SilverBack V

Отзывы:

Похожие инструкции для SilverBack V

Бренды по названию

Популярные бренды

MultiDyne SilverBack V, Руководство по конфигурации и эксплуатации

Результаты поиска

Содержание SilverBack V

Отзывы:

Похожие инструкции для SilverBack V

Бренды по названию

Популярные бренды