3
NOTE: The
BL-KR V1.0
and BL-KR
V2.0 have
identical
hardware
and
software
configurations. The only distinction
is the outside plastic housing.
6.
The App will now search for
devices in range.
7.
Choose the Controller. The serial
numbers that populate the device
list can be found on the label
located on the back of the controller
housing with
the designation
“Default name.”
The App will
indicate that
it is in the
process of
connecting.
8.
Once the
device is connected, it will appear on
the home screen when you launch
the Application.
NOTE: You
can associate
up to 400
devices with
the K-Rain
BL-KR App.
The number
of devices
is limited to
the internal
memory on
the Smartphone/Tablet.
the manufacturer with the plunger
already magnetically latched open,
some zones will default to OPEN.
Follow the start-up procedure
for systems with DC Latching
Solenoids. (Page 09)
CAUTION: For every change
to the program in the Mobile App,
you must exit back to the home
screen and tap the blue TRANSMIT
button (bottom right corner). The
Application aggregates changes
and transmits them to the
controller when you have finished
programming.
CAUTION: Programs A, B,
and C are independent programs,
including start times, run times,
watering days, and water budget.
1. Install the App:
– From the App
Store or Google Play Install
the free K-RainBL App:
2. Install a 9 Volt Battery in the
Controller:
– Unscrew the cap,
remove the seal and fasten the
battery to the correct terminals.
Replace the seal and cap and hand-
tighten the cap to ensure it seals.
NOTE: Before you launch the App,
you will need to enable locations
services on your phone/tablet in
order for the App to geolocate
your device during installation. On
Android, location services must
be enabled in order for the App to
connect to the BL-KR device.
3.
Launch the application on
your Smartphone or Tablet.
4.
Associate the controller with
your phone by tapping the Add a
Controller button.
5.
The app will now ask what type
of Bluetooth device you would like
to add:
200 SERIES WARM CLIMATE HIGH-PROFILE DIRECT DISCHARGE UNIT
Programming Unit
PROGRAMMING HYDRO-GUARD® UNIT FOR OPERATION
Discharged water flushed from the
Hydro-Guard® Unit must be routed
away from the device. For Air Gap
models it is recommended that
a 6" catch pipe (by others) be
installed inside of the 200 Series
Warm Climate's external cabinet.
The catch pipe shall be mounted at
least 3" under the discharge piping
of the 200 Series Warm Climate
(see Typical Installation illustration
on page 2). The 6" pipe shall be
installed a minimum of 24" below
grade before a 90-degree bend or
pipe size reduction. If desired, the 6"
pipe can be reduced to a 3" or 4"
pipe to continue the routing of the
flow to a final discharge point. The
recommended final discharge points
may include a storm drain, drainage
or retention pond, or a storm swale.
Technical Data
• Operating temperature range of
32° to 120° F
• Operating Pressure: 7 to 200 psi
NOTE: Where sustained pressures
may exceed 120 psi the installation
of a pressure reducing valve (PRV)
is recommended.
Battery Life
Will vary based on number of
cycles per year, operating pressure,
and temperature. We recommend
checking the battery every 6 months,
but in many cases, you will get mor
life out of them.
200 Series Warm Climate
(Requires Controller)
The BL-KR battery powered
irrigation module communicates
with the K-Rain BL Application on
a Smartphone or Tablet by using
Bluetooth SMART 4.0, (low energy)
on an iPhone with iOS version 7
minimum or an Android phone/
tablet with Marshmallow version
6.0 or higher.
Important
CAUTION: For use only with
9V DC Latching Solenoids. As
some solenoids will come from
!
!
!
To add
another
controller, tap
the plus sign
in the upper
right hand
corner of the
home screen.
Application Home Screen:
Device Home Screen:
