NASTAVITEV VPLINJA
Č
A / ADJUSTING CARBURETTOR
Prosimo preberite navodila pred prvim zagonom motorja.
Please read the instructions before starting Engine.
1.
2.
3.
4.
5.
6.
[Pred vožnjo]
Vplinja
č
je tovarniško nastavljen za prvi zagon motorja in za njegovo pravilno
vtekanje.
Nastavitev je mogo
č
e potrebna glede na izbrano gorivo in žarilno sve
č
ko.
The Carburetor is already pre-adjusted from the factory for break-in
when starting the engine.
[Before driving]
Adjustments maybe needed according to fuel and glow plug selection.
Main needle Adjusting Screw
Vijak igle za visoke obrate
Closing (lean)
Zapiranje
Opening (rich) Odpiranje
(Nastavitev prostega teka)
(Adjusting Idling)
Odpiranje
Opening (rich)
Closing (lean) Zapiranje
Decreasing RPM Manjšanje obratov
Unscrewing
odvijati
Vijak za nastavitev
postega teka
Idling Adjusting Screw
Vijak igle za nizke obrate
Slow Needle Adjusting Screw
Increasing RPM Višanje obratov
Screwing
privijati
(Nastavitev prostega teka)
Prosti tek je tovarniško nastavljen na 1-1,5mm.
To nam malo zviša obrate motorja za lažji zagon.
Vijak za nastavitev
prostega teka
Idling Adjusting Screw
Manjšanje obratov –
odviti
Decreasing RPM
Unscrewing
Višanje obratov-priviti
Increasing RPM ScrewinQ
(Nastavitev visokih obratov)
Z vijakom za visoke obrate nastavljamo maksimalne obrate.
Za prvo vožnjo ne spreminjajte tovarniških nastavitev.
Z vrtenjem vijaka v desno boste zvišali obrate z vrtenjem v levo pa
zmanjšali.
Č
e boste vijak premo
č
no privili lahko pregrejete motor in ga s
tem uni
č
ite.
(Nastavitev visokih obratov) (Adjusting Main Needle)
Zapiranje
Closing
Odpiranje Opening
Vijak igle za visoke obrate
Main needle Adjusting Screw
(Nastavitev nizkih obratov)
Z vijakom za nizke obrate nastavljamo nizke in srednje obrate.
Za prvo vožnjo ne spreminjajte tovarniških nastavitev. Ko ustavite avto naj
bodo obrati mirni in enakomerni.
Č
e so obrati prenizki pri speljevanju, vijak
postopoma privijajte. Predno za
č
nete spreminjati nastavitve igel vplinja
č
a,
si zapomnite tovarniške nastavitve le-teh.
Nastavitve igel vedno spreminjajte približno za 10-20 stopinj.
(Nastavitev nizkih obratov) (Adjusting Slow Needle)
[Adjusting Idling]
The Idling Adjustment has a factory setting of
1-1.5
mm.
This will increase the RPM for easier starting.
Vijak igle za nizke obrate
Slow Needle Adjusting Screw
[Adjusting Main Needle ]
The main needle screw adjusts maximum RPM.
For the first drive, leave the adjustment in the factory setting.
Turning the needle clockwise will increase RPM and by turning the needle
counter-clockwise will decrease RPM. By turning the needle too much will
cause over-heating and damage to the Engine.
Closing (lean)
Zapiranje
[Adjusting Slow Needle ]
The slow needle adjusts the low and middle RPM. For the first drive, leave the adjustment
in the factory setting. After stopping the car you want the idle to be smooth and consistent RPM. If it has
dull/clumsy feel when taking off, adjust the slow needle clock-wise in small adjustments. You want the
car to take off smooth on the bottom end. Be sure to remember the original settings before adjusting the
needles. Adjust the needle in approx.
10
to
20
degree increments.
Opening (rich)
Odpiranje
Содержание 4WD
Страница 23: ......
