POWER AMPLIFIER OWNER’S MANUAL
6
7
1. Gain Control –
These controls are used to match the input sensitivity of the amplifier position to the
particular source unit that you are using. The controls are factory set to 1Vrms.
2. Crossover Control Front and Rear –
This switch turns the internal electronic high pass
18dB/Octave 85Hz crossovers on and off. If the switch is selecting HP, the crossover is on. When the switch
is selects FR, the crossover is bypassed for a full range output. (Subwoofer is a fixed low pass 18dB/Octave
85Hz crossover)
3. RCA Input Jacks Front and Rear –
RCA or type input jacks for use with source units that have RCA
or Line Level Outputs. A source unit with a minimum output level of 200mV is required for proper operation.
4. Bass EQ –
This equalization circuit is used to enhance the low frequency response of the vehicle’s
interior. With up to 18 dB of boost and centered at 40Hz, the Bass EQ can be adjusted to meet your own
personal taste.
5. RCA Input Jacks (Sub) –
L + R inputs are supplied to simplify installation. The left and right inputs sum
internally to form a single monaural channel. The left and right inputs are electronically isolated and will not
affect the isolation of the other four channels. A source unit with a minimum output level of 200mV is required
for proper operation.
6. EBC –
The EBC, or Electronic Bass Control, allows a remote bass control to be adjusted from the dri-
ver’s seat. If the optional EBC is installed, the bass level will be able to be adjusted to overcome noise
and other interference.
Input Panel Layout
❶
❺
❻
1. Fuses –
For convenience, all amplifiers utilize ATC type fuses. For continued protection in the event that
a fuse blows, replace the fuse only with the same value.
Caution: The power fuses on the amp are for protecting the amp against overdrive. To protect the vehicle’s
electrical system, an additional fuse is required within 18" of the battery on the 12V+ cable.
2. Power Terminal –
This is the main power input for the amplifier and must be connected directly to the
positive terminal of the car battery for the amplifier to operate properly. Use caution when running this cable
through the car. Try to avoid the input RCA cables, antenna cabling, or other sensitive equipment as the large
amount of current flowing through this cable can induce noise into your system. It is also very important to
have a tight connection to ensure maximum performance.
3. Ground Terminal –
A good quality ground is required for your Thunder Amplifier to operate at peak
performance. A short length of cable the same gauge as your power cable should be used to attach the
ground terminal directly to the chassis of the car. Always scrape or sand any painted surfaces to expose
bare metal where the ground wire will attach.
4. Remote Terminal –
All Thunder Amplifiers can be turned on by applying 12 volts to this terminal.
Typically this voltage is supplied by a wire from the source unit marked “remote” or “electric antenna”.
5. Term Block Right Channel –
The Right Rear + and Right Rear – terminals connect the right rear
speaker to the right rear channel of the amplifier. Connect the + terminal of the speaker to the Right Rear +
terminal of the amplifier and the – terminal of the speaker to the Right Rear – terminal of the amplifier. 2 ohm
minimum impedance is allowed. Operation the same for front channels.
6. Term Block Left Channel –
The Left Rear + and Left Rear – terminals connect the left rear speaker
to the left rear channel of the amplifier. Connect the + terminal of the speaker to the left Rear + terminal of
the amplifier and the – terminal of the speaker to the left Rear – terminal of the amplifier. 2 ohm minimum
impedance is allowed. Operation the same for front channels.
7. Term Block Sub Channel –
The sub + and sub - terminals connect the subwoofer to the dedicated sub-
woofer channel of the amplifier. Connect the + terminal of the speaker to the sub + terminal of the amplifier
and the – terminal of the speaker to the sub – terminal of the amplifier. 2 ohm minimum impedance is allowed.
8. Power LED (top of heatsink) -
A lighted LED indicates that power has been applied to the amplifier.
+12V from the battery to the +BATT terminal and +12V from a switched ignition or remote lead from a head
unit. An unlighted LED indicates power has been removed or the amplifier has overheated. In the case of
the overheat condition, the amplifier will turn back on after it cools down.
Output Panel Layout
❶
❹
❺
❷
❸
❼
❶
❶
❷
❷
❹
❸
❻
Содержание THUNDER895
Страница 1: ...POWER AMPLIFIER OWNER S MANUAL...
