background image

D-   

If

 

the MUD amp included with your kit has a High Level switch

, move the 

switch to Low Level. The MTX harness converts the signal to low level to 

correctly work with the MUD amplifier.

E- Turn the gain to max and switch the filter to high pass.

F-  Mount the amplifier to the Harley bracket (Part Number RGBRACKET) as shown in 

the photo. Ensure mounting bolts are tightened down securely. (Mounting hardware 

included with the bracket)

G- Remove The 2 brake side front fork fairing nuts.

H-  Place the amplifier bracket over these 2 bolts, and replace and tighten the 

nuts. The amplifier is now locked in place.(Amp pigtails face upward)

I-  Connect the amplifier connections on the wire harness. There are 3 

connections, 1 large rectangular connector, and 2 bullet power connectors. 

Take care to keep the power wire polarity correct. Red to Red, Black to Black.

       

       

       

       

       

       

       

       

       

a. Make sure the connections are securely snapped together.

J- Open fuse holder and place the 15 amp fuse in the holder.

K-  Turn the bike to ACC and test to make sure the amplifier and speakers power 

up. If all works reverse the process to put the fairing back in place.

-5-

Содержание HDWH2











Отзывы: