background image

Third Step - Speaker Mounting

A-  Place the new speaker along with the speaker ring on the front. This spaces 

the speaker so it fits properly in place according to the below picture to keep 

the terminals in the best location for connecting the speaker wires.

B-  Tighten the 4 speaker screws back up so the unit is tightly held to the fairing.

Fourth Step - Routing the Power Wire and Wire Harness (2 People Suggested 

TEAM LIFT)

A- Run the wire harness along the factory harness.

B- Loosen the front two gas tank bolts using a T40 Torx driver.

C- Loosen the rear gas tank bolt using a T40 Torx driver.

D-  Lift the gas tank up enough to pop open the plastic wire channel on the brake 

side. Take care to not pull out fuel lines. Removal of the gas tank will make 

this much easier. 

E-  Run the wire down though the wire channel and snap the top of the wire 

channel back in place.

F-  The gas tank can be lowered back into place and the mounting bolts can be 

put back and tightened in place.

G- Attach the positive and negative wires to the battery.

Fifth Step - Connect the Amp and Speakers (Road Glide, Road Glide Ultra)

A-  Connect the MTX wire harness to the factory speaker wiring, making sure 

the clutch side and brake side are connected to the correct input wires. The 

wires are marked with a tag on each end. Plug the MTX harness connectors 

into the corresponding factory connectors. Please ensure the connections 

are secure so they do not come loose when riding.

B-  Connect the speaker output wires to the new speakers mounted to the

bike. Also make sure to keep the clutch side and brake connectors 

directed to the correct side. The speaker output wires are marked with a

tag indicating clutch or brake and have female fastons on each end that

will connect to the new speaker.

C-  

Unplug the stock wire connected to the center of the cigarette lighter. Then 

plug in the blue wire from the MTX wire harness into the cigarette lighter, and 

then plug the stock cigarette lighter wire connector into the extra connector 

on the MTX wire harness.

-4-

Содержание HDWH2











Отзывы: