MTU M015710/04E Скачать руководство пользователя страница 111

Страница: 111 / 196

504 – AL CAN POM Node Lost

ZKP-Number: 14.500.904

Cause

Corrective action

POM missing on CAN bus.

Check connection and POM.

506 – AL Low Starter Voltage

ZKP-Number: 14.500.906

Cause

Corrective action

The battery voltage is too low for

the starting process.

Check starter battery and cabling.

507 – AL POM Error

ZKP-Number: 14.500.907

Cause

Corrective action

A general POM fault occurred.

Replace POM.

508 – AL Wrong POM-ID

ZKP-Number: 14.500.908

Cause

Corrective action

POM sends a different ID

number than expected.

Check POM wiring harness.

510 – AL Override applied

ZKP-Number: 27.002.010

Cause

Corrective action

Override was activated.

Deactivate Override pushbutton again.

515 – AL Starter Not Engaged

ZKP-Number: 21.090.926

Cause

Corrective action

Starter on CPM / POM could not

be engaged. If the number of

automatic start attempts from PR

2.1090.134 Number of Start

Attempts is used up then start is

canceled. Check CPM, starter

and cabling.

1. Repeat starting attempt

2. Check CPM, starter and cabling.

126 | Troubleshooting | M015710/04E 2012-09

TIM-ID: 0000008506 - 002

Содержание M015710/04E





































































































































































































Результаты поиска

Содержание M015710/04E

Отзывы:

Бренды по названию

Популярные бренды

MTU M015710/04E, Руководство по эксплуатации

Результаты поиска

Содержание M015710/04E

Отзывы:

Бренды по названию

Популярные бренды