manualshive.com logo in svg

MTU 8V4000Mx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 8V4000Mx4 Скачать руководство пользователя страница 87

4.14 Waterjet – Flushing from LOP (optional)

Preconditions

☑

LOCAL OPERATION illuminated switch is lit brightly (local operating mode is active).

☑

Waterjet-BucketVessel at standstill and waterjet bucket is below the waterline.

☑

Engine speed is in engagement window.

☑

No external engagement interlock is active.

NOTICE

Waterjet flushing puts excessive strain on the bearings.
Bearing damage!
• Do not flush waterjet for too long.
• Follow instructions of the waterjet manufacturer.

Flushing with reversing gearbox and flushing mode

Item

Measure

LOP

Press and hold down FLUSH illuminated pushbutton (→ Page 72).
• FLUSH illuminated pushbutton flashes.
• Gearbox is engaged ASTERN.
• FLUSH illuminated pushbutton is brightly lit after receiving feedback sig-

nal from clutch.

LOP

Release FLUSH illuminated pushbutton.
• FLUSH illuminated pushbutton flashes.
• Gearbox is disengaged (neutral position).
• FLUSH illuminated pushbutton goes out after receiving feedback signal

from clutch.

MS150109/01E 2015-11

| Operation | 87

TIM-ID: 0000002330 - 008

Содержание 8V4000Mx4























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды