MTU 8V4000M*3 series Скачать руководство пользователя страница 156

Страница: 156 / 260

8.5.4 Cylinder head cover – Removal and installation

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 10–60 Nm

F30510423

Ratchet bit

F30027341

Assembly compound (Kluthe Hakuform 30-15)

X00067260

Engine oil
O-ring

(→ Spare Parts Catalog)

Removing cylinder head cover

Clean very dirty cylinder head covers (1) prior
to removal.

Remove screws (3, 4) with washers (2, 5).

Take off cylinder head cover with O-ring (6)
from cylinder head (7).

Installing cylinder head cover

Clean installation surface.

Check O-ring (6) for damage, replace as necessary.

Coat O-ring (6) with assembly compound.

Insert O-ring (6) in groove on cylinder head cover (1).

Place cylinder head cover (7) on cylinder head.

Install cylinder head cover with screws (3, 4) and washers (2, 5).

Tighten screws (3), (4) to specified tightening torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Screw

M10

Tightening torque

(Engine oil)

42 Nm

154 | Valve Drive | MS15034/00E 2018-08

TIM-ID: 0000012309 - 017

Содержание 8V4000M*3 series





































































































































































































































































Результаты поиска

Содержание 8V4000M*3 series

Отзывы:

Похожие инструкции для 8V4000M*3 series

Бренды по названию

Популярные бренды

MTU 8V4000M*3 series, Руководство по эксплуатации

Результаты поиска

Содержание 8V4000M*3 series

Отзывы:

Похожие инструкции для 8V4000M*3 series

Бренды по названию

Популярные бренды