MTU 12V4000C*5 series Скачать руководство пользователя страница 69

Страница: 69 / 305

5 Operation

5.1 Putting the engine into operation after extended out-of-service

periods (>3 months)

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Preservation and Represervation Specifications (A001070/..) are available.

Putting the engine into operation after extended out-of-service periods
(>3 months)

Item

Action

Engine

Depreserve (→ Preservation and Represervation Specifications A001070/..).

Cylinder liner

Perform endoscopic examination of cylinder liner (→ Page 159).

Valve drive

Lubricate valve gear every ≥ 6 months (→ Page 165).

Lube oil system

Check engine oil level (→ Page 202).
Bar engine using starting system (→ Page 155).

Fuel prefilter

Fill with fuel (if fitted).

Coolant circuit

If engine has been out of service for more than 1 year, change engine cool-
ant (→ Page 218).
Change charge-air coolant (→ Page 229).

Coolant circuit

Check engine coolant level (→ Page 216);
Check charge-air coolant level (→ Page 227).

Coolant circuit

Preheat coolant with coolant preheating unit (if available).

Engine governor

Check electrical connections (→ Page 256).

Engine management

Read out fault memory using DiaSys, see (→ manufacturer's documentation).
Check all active fault messages, eliminate faults as necessary (→ Page 81).

MS15041/03E 2018-08

| Operation | 67

TIM-ID: 0000045459 - 002

Содержание 12V4000C*5 series


















































































































































































































































































































Результаты поиска

Содержание 12V4000C*5 series

Отзывы:

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 69 / 305

Результаты поиска

Содержание 12V4000C*5 series

Отзывы: