manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 157 / 305

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 157

8.1.2 Engine – Barring with starting system

DANGER

Rotating and moving engine parts.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Before barring the engine, make sure that there are no persons in the engine's danger zone.
• After finishing work on the engine, make sure that all safety devices are put back in place and all

tools are removed from the engine.

Engine – Barring with starting
system

1.

Release latch (1) of connector X3 (2).

Note:

Seal unused connectors with the supplied
protective cap.

2.

Remove connector from engine governor.

3.

Turn engine in unloaded condition: Press
START button.

4.

Let the crankshaft rotate until oil pressure is
indicated.

5.

Engine start is interrupted automatically after
the maximum permissible time.

6.

Repeat this procedure after approximately
20 seconds if required.

7.

Fit connector X3 (2) on engine governor and
close latch (1).

MS15041/03E 2018-08

| Engine | 155

TIM-ID: 0000029454 - 004

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов