manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 229 / 305

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 229

8.16 Low-Temperature Circuit

8.16.1 Charge-air coolant level – Check

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Fluids and Lubricants Specifications (A001061/..) are available.

DANGER

Falling from great heights.
Risk of serious injury – danger to life!
• When working high on the equipment, always use suitable ladders or work platforms.
• Use personal protective equipment.

WARNING

Coolant is hot and under pressure.
Risk of injury and scalding!
• Let the engine cool down.
• Wear protective clothing, gloves, and goggles / safety mask.

WARNING

Coolant contains antifreeze and is toxic.
Risk of poisoning and slipping!
• Avoid contact with eyes and skin.
• Do not inhale vapors or mist, wear breathing protection.
• Do not eat, drink, smoke when working with antifreeze.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Wipe up escaped/spilled coolant immediately.

Checking charge-air coolant level at filler neck

1.

Turn cover on coolant expansion tank counterclockwise to the first stop and allow pressure to escape.

2.

Continue to turn cover counterclockwise and remove.

Note:

Charge-air coolant must be visible at marker
plate.

3.

Check charge-air coolant level.

4.

Top up charge-air coolant as necessary
(→ Page 233).

5.

Check that cover is in serviceable condition.

6.

Clean sealing surfaces as necessary.

7.

Fit cover and close it.

MS15041/03E 2018-08

| Low-Temperature Circuit | 227

TIM-ID: 0000000042 - 009

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов