MTU 12V2000B26F Скачать руководство пользователя страница 117

Страница: 117 / 147

Measuring belt tension with frequency meter

Remove protective cover.

Tap against the belt with the handle of a hammer or with a wrench to initiate belt vibration.

Hold measuring tip of the frequency meter over belt drive.

The measured frequency value appears on the display of the frequency meter.

Compare measured value with value in the table.

If the measured values deviate from the specified values, adjust drive belt tension (→ Page 118).

Install protective cover.

Belt length ‒ Application

Measured value
Initial installation (new belt)

Measured value
Operating tension (used belt)

Drive belt 1800 mm – Fan

Frequency: 88 ±1 Hz

Frequency: 77 ±1 Hz

Drive belt 1520 mm – Fan

Frequency: 104 ±1 Hz

Frequency: 92 ±1 Hz

Table 114: Set-point values ‒ Measurement with frequency meter

MS150118/00E 2014-07

| Task Description | 117

TIM-ID: 0000053489 - 001

Содержание 12V2000B26F




















































































































































Результаты поиска

Содержание 12V2000B26F

Отзывы:

Бренды по названию

Популярные бренды

MTU 12V2000B26F, Руководство по эксплуатации

Результаты поиска

Содержание 12V2000B26F

Отзывы:

Бренды по названию

Популярные бренды