MTU 12 V 4000 G21R Скачать руководство пользователя страница 38

Страница: 38 / 117

Fault

code

Alarm text

Meaning

Task

211

SD P-LUBE OIL

Sensor defect (lube oil pres‐

sure)

1. Check wiring.

2. Contact Service.

215

SD P-RAIL FUEL Sensor defect (common rail

pressure);
HP controller in emergency

mode

1. Check wiring.

2. Contact Service.

216

SD T-LUBE OIL

Sensor defect (lube oil tem‐

perature)

1. Check wiring.

2. Contact Service.

220

SD COOLANT

LEVEL

Sensor defect (coolant level)

1. Check wiring.

2. Contact Service.

223

SD LEVEL IN‐

TERCOOLER

Sensor defect (charge-air

coolant level)

1. Check wiring.

2. Contact Service.

229

SD ENG.SPEED

SENSORS

Sensor defect (crankshaft

speed) and sensor defect

(camshaft speed)

1. Check wiring.

2. Contact Service.

230

SD CRANK‐

SHAFT SPEED

Sensor defect (crankshaft

speed)

1. Check wiring.

2. Contact Service.

231

SD CAMSHAFT

SPEED

Sensor defect (camshaft

speed)

1. Check wiring.

2. Contact Service.

240

SD P-FUEL

Sensor defect (fuel pressure)

1. Check wiring.

2. Contact Service.

245

SD POWER

SUPPLY

Sensor defect (engine gover‐

nor operating voltage)

Contact Service.

246

SD T-ELEC‐

TRONIC

Sensor defect (temperature in

engine governor)

Contact Service.

250

SD CAN SPEED

DEMAND

Sensor defect (CAN nominal

speed demand)

1. Check speed transmitter.

2. Check wiring (CAN bus).

3. Contact Service.

266

SD SPEED DE‐

MAND AN.

Sensor defect (analog nomi‐

nal speed demand)

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

267

SP.DEM.TEST

BENCH

Sensor defect (analog speed

demand);
NOTE:
Only used in test-stand opera‐

tion.

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

270

SD SPEED DE‐

MAND FI1

Sensor defect (frequency in‐

put for speed demand);

1. Check speed transmitter.

2. Check wiring.

3. Contact Service.

271

SD T-EXTERN 1 External device defective

(CAN T-EXTERN 1)

Contact Service.

272

SD T-EXTERN 2 External device defective

(CAN T-EXTERN 2)

Contact Service.

273

SD P-EXTERN 1 External device defective

(CAN P-EXTERN 1)

Contact Service.

274

SD P-EXTERN 2 External device defective

(CAN P-EXTERN 2)

Contact Service.

MS150064/01E 2011-11 | Troubleshooting | 57

TIM-ID: 0000003158 - 001

Содержание 12 V 4000 G21R






















































































































Результаты поиска

Содержание 12 V 4000 G21R

Отзывы:

Похожие инструкции для 12 V 4000 G21R

Бренды по названию

Популярные бренды

MTU 12 V 4000 G21R, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 4000 G21R

Отзывы:

Похожие инструкции для 12 V 4000 G21R

Бренды по названию

Популярные бренды