MTI Versa EX Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 9

MTI Versa EX Скачать руководство пользователя страница 3

1

1

3

2

Place Pairing Card over the RFID icon to place Versa EX in pairing mode. LED will be flashing blue.

Position connects successfully

to mesh network:

Position fails to connect to mesh

network within 3 minutes:

V

ERSA KE

Y

™

NETWORK PAIRING

Slow Beeps

Double Beep

Four Fast Reject Beeps

VERSA EX

™

PRODUCT MANUAL

3

MTI P/N 063-00393 rev A ©2021 MTI All Rights Reserved

www.mtigs.com | T:800.426.6844

PAIRING VERSA EX

ENTER NETWORK MODE FOR FREEDOM MICRO II

KEY WHITELIST

Place Authorization Card over the
RFID icon to register to system.
LED will be solid blue.

System must be disarmed

to perform this operation.

Place the User Key over the RFID
icon you want to add.

If successful



unit beeps 2 times

If unsuccessful



unit beeps 4

times (retry)

Repeat process for all User Keys
until they are successfully added.

To close the whitelist mode, place
the Authorization Card over the
RFID icon. Whitelist mode will end
automatically after 3 minutes of no
use. LED will double flash yellow
every 8 seconds on initial setup,
indicating no positions are paired
to Versa EX.

«
1
2
3
4
5
...
»

Содержание Versa EX










Отзывы:

Нет отзывов