MTI RAPIDDOC LITE Скачать руководство пользователя

Страница: 9 / 12

RAPIDDOC

™

LITE INSTALLATION GUIDE

www.MTIGS.com | T:800.426.6844

Docking

The case is secure when it clicks into the base.

Dock the case to the base by moving case towards the
base, aligning the disk on the case to the disk on the
base.

NOTE: Wait 30 seconds between Access Card swipes or the latches

may overheat. The LED will start Flashing Orange. Wait until the

flasing stops (approximately 2 minutes) and Try again. If your tablet does

not release, try using the Red Handle Tool to manually remove the tablet.

RFID Release

Within five seconds, remove the case away from the
base. If the case is not removed within five seconds, the
lock will re-engage. Up to 10 access tries are allowed,
then a two minute waiting period before another try will
be triggered.

Place a registered Access Card on the RFID module, the
LED indicator will begin to flash.

-CONTROLLED DOCUMENT-

063-00223

C-0

Status: Approved

ECO-111786

Содержание RAPIDDOC LITE













Результаты поиска

Содержание RAPIDDOC LITE

Отзывы:

Похожие инструкции для RAPIDDOC LITE

Бренды по названию

Популярные бренды

MTI RAPIDDOC LITE, Руководство по установке

Результаты поиска

Содержание RAPIDDOC LITE

Отзывы:

Похожие инструкции для RAPIDDOC LITE

Бренды по названию

Популярные бренды