MTHTrains Premier EMD SD-80MAC Diesel Engine Скачать руководство пользователя страница 5

Страница: 5 / 50

Figure 5: 2-Rail/3-Rail Operation

3-Rail Pickups

Configuring Locomotive for 2-Rail or 3-Rail Operation

(

As shown in figure 4, the 2Rail/3Rail switch is located underneath the one of the trucks

). Your

locomotive can be configured to operate on 2-Rail or 3-Rail track. From the factory the
locomotive is configured to operate on 3-Rail Track. To configure the locomotive for 2-
Rail track operation, please do the following:

1. Remove the center rail pickup roller assemblies as seen in figure 5.

2. Change the power input from 3-Rail to 2-Rail as seen in figure 4.

Figure 4: 2Rail/3Rail Switch & Smoke Control

2Rail/3Rail Switch

Premier EMD SD-80/90 MAC Diesel Engine w/Proto-Sound 3.0

Содержание Premier EMD SD-80MAC Diesel Engine



















































Результаты поиска

Содержание Premier EMD SD-80MAC Diesel Engine

Отзывы:

Похожие инструкции для Premier EMD SD-80MAC Diesel Engine

Бренды по названию

Популярные бренды

MTHTrains Premier EMD SD-80MAC Diesel Engine, Руководство оператора

Результаты поиска

Содержание Premier EMD SD-80MAC Diesel Engine

Отзывы:

Похожие инструкции для Premier EMD SD-80MAC Diesel Engine

Бренды по названию

Популярные бренды