MTHTrains Bavarian Class S 3/6 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 51

background image

M.T.H. HO S 3/6 Steam Engine

27

Advanced DCC Operation:

This section of the manual provides more in-depth detail on how to set up and
configure your MTH PS3.0-equipped engine using the NMRA-standard CV's as
well as the manufacturer-specific CV's. It also explains some of the other F
Functions not covered in the Basic DCC Operation section. Please refer to the CV
Data Table on

page 28.

Configuration Variables (CV)

Configuration Variables used on MTH PS3.0-equppied engines.

Cv1
Cv2
Cv3
Cv4
Cv5
Cv8
Cv17
Cv18
Cv19

Cv21
Cv22

Cv23
Cv24
Cv25
Cv29
Cv52
Cv53

Cv54
Cv55

Cv56
Cv63
Cv64
Cv66
Cv67-
Cv94
Cv95
Cv105
Cv106
Cv115-

CV170

Short Address: 1-127 are the valid addresses
Start Voltage (CV52, bit0 must =1. This will enable PWM Mode)
Acceleration Rate (CV52, bit0 must =1. This will enable PWM Mode)
Deceleration Rate ((CV52, bit0 must =1. This will enable PWM Mode)
Max Voltage (CV52, bit0 must =1. This will enable PWM Mode)
MFG ID. MTH =27. Also used for various resets
High Byte of Extended Address
Low Byte of Extended Address
Consist Address (bit 7=1 on an engine will tell the engine it's reversed in a

consist)
Defines active Function F1-F8 for the active consist
Defines active functions for FL and F9-F12 for the active consist (bit 0=1 will

tell an engine that you want it's FL control to operate under the consist address

– bit1-0/bit2=1 will configure the FL control for a reversed engine in a consist)
Consist Acceleration Rate
Consist Deceleration Adjustment
Speed Table Select
Decoder Configuration
MTH PWM Mode Configuration
MTH Acceleration (1/8*sMPH/s). For example – a Value of 8 written would

give you 1sMPH/s acceleration
MTH Deceleration Rate (1/8*sMPH/s)
Factory Reset Alternate method: Send a value of 55 to CV55 on address 55 and

the model will go back to Factory Default
Motorola Operating Mode (Applies to 3E+ models)
MTH Consist Acceleration Rate (1/8*sMPH/s)
MTH Consist Deceleration Rate (1/8*sMPH/s)
Forward Trim (CV52, bit0 must =1. This will enable PWM Mode)
Speed Table Selection (CV29 bit 4 must be set to 1 then CV25 must be set
to 0 or 1)
Reverse trim (CV52, bit0 must =1. This will enable PWM Mode)
User ID #1 – General Purpose use for customer
User ID #2 – General Purpose use for customer
MTH Function Assignments – See table of supported CV's and manual section

on how to re-arrange them for further information

«
...
25
26
27
28
29
...
»

Содержание Bavarian Class S 3/6




















































Отзывы:

Нет отзывов

Похожие инструкции для Bavarian Class S 3/6

Бренд: Faller Страницы: 16

Бренд: Tumama Kids Страницы: 24

Branchline Class 03

Бренд: Bachmann Страницы: 3

Бренд: Old School Model Works Страницы: 22

Бренд: Joustra Страницы: 16

Бренд: Step2 Страницы: 4

Бренд: Faller Страницы: 16

Malpad Magic Glow KM001

Бренд: easymaxx Страницы: 6

Бренд: ROBBE Страницы: 12

Jaguar A exterior

Бренд: Eduard Страницы: 4

Kids Supemarket

Бренд: Mocka Страницы: 20

Spinning Tunes Music Player

Бренд: VTech Страницы: 10

A-7D/E Corsair II

Бренд: Jet Hangar Страницы: 66

U.S.S. New Jersey BB-62 (1982)

Бренд: REVELL Страницы: 25

PRR E6s Atlantic

Бренд: Accucraft trains Страницы: 9

Бренд: Smoby Страницы: 12

Бренд: REVELL Страницы: 12

Бренд: Adrian Olson Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды