background image

T41 SERIES

MTH PUMPS

Section T41 Page 516

Dated January 2000

97-4622-01-588

MTH Tool Company, Inc. / MTH Pumps,
hereinafter referred to as “MTH”, war-
rants for a period of twelve (12) months
from the date of shipment (“The Warranty
Period”), that the pumps manufactured
by it will be free from defects in material
and workmanship.  MTH will correct de-
fects in material or workmanship which
may develop in its products under proper
or normal use during the Warranty Period
and under the conditions of this Warran-
ty.  This Warranty does not extend to
anyone except the original consumer-
purchaser.  Damage to the product due to
improper handling, improper storage,
improper maintenance, or improper ap-
plication is not covered by this Warranty.
Warranty claims for motors, mechanical
seals, and accessories should be direct-
ed to those who manufactured the
component.  MTH will repair or replace, at
its option and expense, its products
proved to be defective after examination

by the Company.  The defective Product
must be returned, transportation prepaid, to
the factory at Plano, Illinois.  Disassembly of
the equipment impairs determination of
reasons for failure and shall be cause for
voiding this Warranty.  The Product, re-
paired or replaced, will be shipped f.o.b.
MTH’s factory.  This is MTH's sole warran-
ty.    MTH makes no other warranty of any
kind, expressed or implied, and all im-
plied warranties of merchantability and
fitness for a particular purpose which
exceed MTH's aforestated obligations
are hereby disclaimed by MTH and ex-
cluded from this warranty. 
 MTH neither
assumes nor authorizes any person to as-
sume for it, any other obligation in
connection with the sale of the Product and
any enlargement of this Warranty by a pur-
chaser shall be for its own account and its
exclusive responsibility.  This Warranty
shall not apply to any Product or parts of
Products which:  (a) have been repaired or

7.

Limited Warranty

altered outside of MTH’s factory, in any
manner; or (b) have been subjected to
misuse, negligence or accident; or (c)
have been used in a manner contrary to
MTH’s printed instructions; or (d) have
been damaged due to defective power
supply or faulty installation.    MTH shall
not be liable for incidental and conse-
quential losses and damages under
this express warranty, any applicable
implied warranty, or claims for negli-
gence, except to the extent that this
limitation is found to be unenforceable
under the applicable State law.  Some
States do not allow the exclusion or
limitation of incidental or consequen-
tial damages, so the above limitation
or exclusion may not apply to you.
This warranty gives you specific legal
rights, and you may also have other
rights which vary from State to State.

A. Parts
B. Repair Service
C. Warranty Service
D. Motors, Mechanical Seals,

and Accessories

6A Parts

Repair parts may be obtained through
your local Authorized MTH Pumps
Representative or Distributor who can
be found in the yellow pages or by
contacting MTH Pumps at 401 W. Main
St. • Plano, IL 60545  Phone: 630-552-
4115
Fax: 630-552-3688.

6B Repair Services

Repair service for an MTH pump
should be obtained from the company
through which it was purchased.

6.

In the event this is not possible, the name
and phone number of a nearby MTH
representative or distributor may be
obtained by contacting MTH Pumps.  In
the event that it is necessary to return the
pump to the factory for repairs, remove all
accessories attached to the pump.  We
cannot accept responsibility for their safe
removal, storage, and return.

6C Warranty Service

All requests for warranty claims should be
made through the company from which
the pump was purchased or supplied.
Complete details on what is wrong with
the pump must be provided along with
information on the system in which it is
installed.  Refer to the MTH Pumps
Limited Warranty statement.  Return
authorization must be obtained prior to
returning any equipment.

6D Motors, Mechanical Seals, and
Accessories

Repair or replacement service on
motors, mechanical seals, relief valves,
or other accessories should be obtained
from the manufacturer of these
components. MTH does not carry
replacement parts and is not authorized
to render repair service on these
components.  Replacement mechanical
seals are stocked at MTH and are
always available insofar as possible for
immediate shipment.  Warranty service,
as well as expert application informa-
tion can be obtained from your local
seal manufacturer's sales office.

Parts and Repair Services

T41 SERIES

Содержание T41 Series

















Отзывы: