background image

16

S

ection

 7— S

ervice

7. 

Carefully tilt and support the unit up to provide access 

underneath to the nozzle mounting hardware and impeller. 

Remove the three shoulder bolts securing the black plastic 

lower flail housing to the lower housing. Refer to Figure 

7-4.

Figure 7-4

8. 

Tilt top of black plastic lower flail housing toward the 

engine to remove.

9. 

Using a 3/16” allen wrench, remove the flat head cap 

screws that hold the chipper blade to the impeller. These 

screws are accessible through the opening created when 

the chipper chute was removed earlier. See Figure 7-5.

Chipper 

Blade

Flat Head 

Cap Screws

Figure 7-5

10.  The nuts on the flat head cap screws can be reached 

from underneath using a 1/2-inch socket, universal, and 

extension. See Figure 7-6.

Nuts

Impeller

Figure 7-6

11.  Replace or sharpen chipper blade. The blade can be 

sharpened with a file or on a grinding wheel.

WARNING: 

The chipper blade is sharp. When 

sharpening blade, wear leather work gloves to 

protect your hands and follow the original angle of 

grind.

12.  Reassemble by performing the previous steps in the 

opposite order and manner of removal.

NOTE: 

Tighten blade screws to 210 - 250 in-lbs. Make 

certain chipper blade is reassembled with the sharp edge 

facing upward.

Off-Season Storage

• 

When storing the chipper/shredder vacuum in an 

unventilated or metal storage shed, care should be taken 

to rustproof the non-painted surfaces. Using a light oil 

or silicone, coat the equipment, especially any springs, 

bearings, and cables.

• 

Remove all dirt from exterior of engine and equipment.

• 

Follow lubrication recommendations.

• 

Refer to engine manual for correct engine storage 

instructions.

• 

Store equipment in a clean, dry area. Do not store in an 

area where equipment is present that may use a pilot light 

or has a component that can create a spark.

Содержание Rover CSV 060





















Отзывы: