background image

I

   Introduction    1

1  Introduction

This chapter contains general information on the MTD-ERV 350.

1.1  Foreword

Apart from this general chapter, this operating man-
ual consists of:
•  A section for the user,
•  A section with technical specifi cations, and …
•  A section for the installer.

-

e

b

 

y

ll

u

f

e

r

a

c

 l

a

u

n

a

m

 

g

n

it

a

r

e

p

o

 

s

i

h

d

a

e

R

 
fore putting the unit into operation.
 - User 

 Chapters 1 to 3.

 - Installer 

 Chapter 4.

This operating manual contains all the information 
required for safe and optimum installation, opera-
tion and maintenance of the MTD-ERV 350. In ad-
dition, it should serve you as a reference manual 
during  service  work  so  that  this  can  be  carried 
out safely and responsibly. The unit is subject to 
ongoing  improvement  and  further  development. 
Your  MTD-ERV 350  may  therefore  differ  slightly 
from the descriptions in this operating manual.

NOTE:

This manual has been produced with the 

greatest care and attention. However, no 

rights can be derived from this. Furthermore, 
the company reserves the right to change the 
contents of this operating manual at any time 

without prior notifi cation.

1.2  CE Symbol

The unit is marketed under the name MTD-ERV 350.
The MTD-ERV 350 is a balanced ventilation system 
with heat recovery for healthy, balanced and ener-
gy-saving ventilation of living premises.
The year of construction of the MTD-ERV 350 is 
shown on the identifi cation plate of the ComfoAir 
350.

1.3  Warranty and Liability

1.3.1  General

Our “General Terms and Conditions” in their latest 
wording apply to the MTD-ERV 350. The warranty 
period  begins  with  commissioning,  but  not  later 
than one month after delivery. This applies to ma-
terial replacement and does not include labour. It 
applies only on proof of maintenance having been 
performed by a specialist company in accordance 
with our instructions.

1.3.2   Warranty Terms

The manufacturer's warranty on the MTD-ERV 350 
is for a period of 24 months after installation, but up 
to a maximum of 30 months after the date of manu-
facture of the  MTD-ERV 350. Warranty claims can be 
made only for material fl aws and/or design errors 
discovered during the warranty period. In the event 
of a warranty claim, the MTD-ERV 350 must not be 
dismantled without the prior written authorisation 
of the manufacturer. The manufacturer's warranty 
covers spare parts only if these have been installed 
by an installer approved by the manufacturer.

The warranty will be voided if:

•  The warranty period has expired;
•  The unit is operated without fi lter;
•  Parts not supplied by the manufacturer are in-

stalled;

•  Unauthorised changes or modifi cations are 

made to the unit.

1.3.3   Liability

The MTD-ERV 350 has been developed and manu-
factured for use in "balanced ventilation systems". 
Use in any other way does not constitute an 'intend-
ed use' and can result in damage to the MTD-ERV
350 or in personal injury for which the manufacturer 
accepts no liability.
The manufacturer accepts no liability for damage or 
injury resulting from the following causes:

•  Failure to observe the safety, operating and 

maintenance instructions contained in this op-
erating manual.

•  Installation of spare part not supplied by the 

manufacturer.

•  The responsibility for the use of such spare 

parts lies solely with the installer.

•  Normal wear.

Содержание MTD-ERV 350

























































Отзывы: