MTD 590-303-000 Скачать руководство пользователя страница 9

9

Assembling Discharge Chute

Attach retainer hook, from Group E of hardware 
pack, to the blank hole on the deck as shown in 
Figure 12. Secure with a self-tapping screw. 

Attach one of the two retainer straps to the 
discharge chute with a hex bolt, flat washer and 
flange nut as shown in Figure 13. Repeat with the 
second retainer strap on the other side.

Attach the chute strap to the discharge chute at the 
remaining hole with a hex bolt, flat washer and 
flange nut. See Figure 13.

Position the 12" trim seal along the top edge of the 
discharge chute assembly as shown in Figure 13, 
then press the trim seal fully onto the edge.

NOTE: 

Any or all these straps may already be pre-

assembled at the factory. If so, proceed to next step.

Figure 13

Raise the deck to its highest position. 

Raise the chute deflector on the deck and hold it 
while you position the discharge chute over the 
chute opening.

Insert the hinge pin of the discharge chute into the 
tube on the chute stop bracket. See Figure 14.

Rotate chute around the deck so that its bottom 
edge fits under the deck opening and the top edge 
fits over the back edge of the deck. 

Lower the chute deflector slowly. 

Attach chute strap to the retainer clip on the deck.

Figure 14

Insert a grasscatcher pin through the hole on the 
chute tube as shown in Figure 15. Secure it with a 
flange lock nut from inside the chute tube. Both are 
in Group E of the hardware pack. 

Attach the remaining grasscatcher pin at the 
second hole on the chute tube.

Figure 15

Insert the lower end of the chute extension over the 
discharge chute so that its two notches fit into the 
two corresponding notches on the discharge chute. 

Insert the curved end of the chute tube into the hole 
in the grass bag cover.

Insert the other end of the chute tube into the open 
end of the chute extension. Refer to Figure 13.

Chute

Extension

Retainer Strap*

Hex Bolt

Flat Washer

Flange Nut

Chute
Strap*

Flange Nut

Flat Washer

* May already be pre-assembled

Trim Seal

Discharge
Chute

Insert hinge 

Hinge Pin

Chute Deflector

pin here

Grasscatcher
Pin

Flange Lock 
Nut

Chute Tube

Содержание 590-303-000













Отзывы: