MTD 19A70034OEM Скачать руководство пользователя страница 4

4

S

ECTION

 2 — I

MPORTANT

 S

AFE

 O

PERATION

 P

RACTICES

Safety Symbols

This table depicts and describes safety symbols that may appear on this product.  Read, understand, and follow all instructions on the 

machine before attempting to assemble and operate.

Symbol

Description

3&"%5)&01&3"5034."/6"- 4

 

Read, understand, and follow all instructions in the manual(s) before attempting to 

assemble and operate

STOP 

Turn off the engine before opening the bagger cover.

3. 

Use slow speed. Choose a low enough speed setting so 

that you will not have to stop or shift while on the slope. 

Tires may lose traction on slopes even though the brakes 

are functioning properly. Always keep machine in gear 

when going down slopes to take advantage of engine 

braking action.

4. 

Follow the manufacturer’s recommendations for wheel 

weights or counterweights to improve stability.

5. 

Keep all movement on the slopes slow and gradual. Do 

not make sudden changes in speed or direction. Rapid 

engagement or braking could cause the front of the 

machine to lift and rapidly flip over backwards which could 

cause serious injury.

6. 

Avoid starting or stopping on a slope. If tires lose traction, 

disengage the blade(s) and proceed slowly straight down 

the slope.

Do Not: 

1. 

Do not turn on slopes unless necessary; then, turn slowly 

and gradually downhill, if possible.

2. 

Do not mow near drop-offs, ditches or embankments. The 

mower could suddenly turn over if a wheel is over the edge 

of a cliff, ditch, or if an edge caves in.

3. 

Do not try to stabilize the machine by putting your foot on 

the ground.

4. 

Do not use a grass catcher on steep slopes. 

5. 

Do not mow on wet grass. Reduced traction could cause 

sliding.

General Service

1. 

#FGPSFDMFBOJOHSFQBJSJOHPSJOTQFDUJOHNBLFDFSUBJOUIF

blade(s) and all moving parts have stopped. Disconnect the 

spark plug wire and ground against the engine to prevent 

unintended starting.

2. 

Keep all nuts, bolts, and screws tight to be sure the 

equipment is in safe working condition. 

3. 

Never tamper with your mower’s safety interlock system 

or other safety devices. Check their proper operation 

regularly.

4. 

Never attempt to make adjustments or repairs while the 

mower’s engine is running.

5. 

Grass catcher components and the discharge cover are 

subject to wear and damage which could expose moving 

parts or allow objects to be thrown. For safety protection, 

frequently check components and replace immediately 

with original equipment manufacturer’s (O.E.M.) parts only, 

listed in this manual. Use of parts which do not meet the 

original equipment specifications may lead to improper 

performance and compromise safety! 

6. 

Maintain or replace safety and instruction labels, as 

necessary.

WARNING!

 

Your Responsibility—Restrict the use of this power machine to persons who read, understand and 

follow the warnings and instructions in this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Содержание 19A70034OEM





















Отзывы: