MTD 190-181 Скачать руководство пользователя страница 8

8

Attach the grass bags using the slots shown in 
Figure 6. Close the grasscatcher cover.

Figure 6

Attaching Blades

Remove the blades from your tractor’s deck as follows.

Remove the cutting deck from beneath the tractor, 
(refer to 

Deck Removal

 in the 

MAINTENANCE

 section of 

your tractor’s operator’s manual for detailed 
instructions) then gently flip the deck over to 
expose its underside.

Place a block of wood between the center deck 
housing baffle and the cutting blade to act as a 
stabilizer. See Figure 7.

Use a 15/16" wrench to remove the hex flange nut 
that secures the blade to the spindle assembly. See 
Figure 7.

Figure 7

NOTE: 

The hex flange nut has a right-handed thread

pattern. Do NOT attempt to force the nut in an incorrect
direction. Doing so may damage the nut and create a
safety hazard.

Attach the new blades, included in the bagger kit, to 
your tractor’s deck as follows:

Install the new blades packed with the bagger. Be 
sure to install the blade with the side of the blade 
marked ‘‘Bottom’’ (or with a part number stamped in 
it) facing the ground when the mower is in the 
operating position.

 Mount the SMALLER of the three blades to the 
CENTER spindle. The remaining two blades are 
interchangeable.

IMPORTANT: 

 Use a torque wrench to tighten the blade 

spindle hex flange nut to between 70 foot-pounds and 
90 foot-pounds.

Remount the cutting deck. 

Attaching Discharge Chute

Raise the deck to its highest position. 

On older models:

 Remove the clip, if already 

installed on the deck next to the discharge chute 
opening, by removing the lock nut, spring washer 
and hex bolt that secure it. See Figure 8A.

On older models: 

A grasscatcher pin (G in Figure 

2) and nut (H in Figure 2) have been supplied 
among the loose parts. Attach these to the deck in 
place of the clip just removed. Follow Figure 8B for 
order of assembly. Secure the pin tightly.

Figure 8

Slots

Grass Bag

Grass

Bag

Cover

Spindle Assembly

Hex Flange Nut

Wood Block

Hex  Bolt

Spring

Washer

Hex  Lock 

Cutting 
Deck

Clip

Nut

Grasscatcher 

Pin

Nut

Deck

A

B

Содержание 190-181













Отзывы: