MTD 190-181 Скачать руководство пользователя страница 7

7

SECTION 3:  ASSEMBLY 

NOTE:

 

References to LEFT, RIGHT , FRONT and 

REAR of the tractor are from the operator’s position. 

Before

 assembly, place the tractor on a firm, level 

surface, disengage the PTO, stop the tractor 
engine and set the parking brake.

Mounting Bracket Assembly

Tractors equipped with Shoulder Bolt A 

(refer to Figure 3)

NOTE: 

For convenience, pivot the seat forward and

leave it in that position until the grass collector is fully
mounted and assembled.

Remove the hairpin clip and clevis pin from the rear 
of the mounting bracket assembly.

Position the hooked ends of the bracket assembly 
to the outside of the hitch plate and over the 
shoulder bolts. See Figure 3.

Figure 3

Reinsert the clevis pin through the aligned holes 
(Figure 3) in both the bracket assembly and the 
hitch plate and secure with the hairpin clip. Refer to 
Figure 5.

IMPORTANT:

 There are two holes in the clevis pin. Be 

sure to insert the hairpin clip in the 

upper

 hole to 

properly secure the bracket assembly to the hitch plate.

Tractors without Shoulder Bolt A 

Insert shoulder bolt (C in Figure 2) through a bell 
washer (B in Figure 2) and insert the bolt through 
the support bracket (F in Figure 2). Secure with nut 
(A in Figure 2). See Figure 4.

Place one support bracket on each side of the 
tractor frame aligning the two smaller holes on the 
bracket with corresponding holes on the tractor 
frame. See Figure 4. Secure with self-tapping 
screw (E in Figure 2). 

Remove the hairpin clip and clevis pin from the rear 
of the mounting bracket assembly.

Position the hooked ends of the mounting bracket 
assembly to the outside of the hitch plate and over 
the shoulder bolts just installed on both sides of the 
tractor frame.  Follow arrows in Figure 4.

Align the hole at the rear of the mounting bracket 
assembly to the hole on the hitch plate and re-insert 
the clevis pin through these two holes. Secure with 
the hairpin clip removed earlier.

IMPORTANT: 

Be sure to insert the hairpin clip in the 

upper hole of the clevis pin.

Figure 4

Attaching Grasscatcher Cover and Bags

Place the grasscatcher cover assembly’s support 
tube in position on the rear of unit by sliding the 
support tube down through the center hole in the 
mounting bracket assembly. See Figure 5.

Figure 5

Shoulder Bolt A

Mounting
Bracket

Ali

gn

 th

es

ho

les

Bolt

Shoulder

Self-Tapping

Screw

Hitch Plate

Support Bracket

Nut

Mounting 

Bracket

Washer

Bell 

Mounting 
Bracket

Support

Tube

Clevis
Pin

Hairpin
Clip

Hitch Plate

NOTE:

 Grasscatcher cover not shown here for clarity

Содержание 190-181













Отзывы: