manualshive.com logo in svg

MSA OptimAir MM PAPR, Руководство по эксплуатации

Поделиться
Скачать
MSA OptimAir MM PAPR Скачать руководство пользователя страница 10

(1)

Line up the key in the charger cable plug with the slot in the female connector on the
battery pack.

(2)

Push the plug into the female connector and turn the ring to secure it.

(3)

Plug the charger into a 115-120 V, 50, 60 Hz (standard AC) outlet. The charger can be used internationally with the
appropriate adapter.

CAUTION!

Voltages lower than 115V are not recommended. Voltages greater than 120V will damage the battery charger and battery pack.

Failure to follow this caution can result in battery or equipment damage.

(4)

Charge the battery pack until a full charge is indicated.

LED Signaling

Condition

LED Indication

No Battery

Yellow

Charge Initialization

Yellow

Rapid Charge

Orange

Charge Top-Off

Green/Yellow

Trickle Charge

Green

Charge Error

Orange/Green

The charger uses one LED. When the battery is charging, the LED will be orange. When the LED is green the battery is fully
charged. The battery can stay connected to the charger until it is needed. If the LED is yellow, the battery is either not

connected or not at the proper temperature. The charging will start when the battery pack reaches the optimum charging
temperature of 35°F to 100°F. If the LED is orange/green , there is a failure. Disconnect battery pack, and unplug charger. Plug
charger back into outlet and reconnect battery pack to reset charger. If the LED is orange/green during any part of the charge,
after it has been reset, remove the battery from service.

10

OptimAir® MM PAPR

3 Charging the Battery Pack

US

Содержание OptimAir MM PAPR









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды