MrCool MCDP Series Скачать руководство пользователя страница 9

Страница: 9 / 14

REMOVE ACCESS PANEL

REMOVE RUBBER PLUG FROM BOTH LIQUID

AND SUCTION LINES

NITROGEN

HIGH

LOW

EITHER REMOVE OR PUSH PIPE WRAPPING BACK

THROUGH HOLE IN PIPING PLATE BEFORE LINE

SET CONNECTION AND BRAZING.

CONNECT PIPES

CONNECT GAUGES AND

START NITROGEN FLOW

PLACE A WET RAG AGAINST PIPING

PLATE AND AROUND THE SUCTION

LINE CONNECTION.

BRAZE CONNECTION. ALLOW PIPE TO

COOL BEFORE REMOVING WET RAG

FROM TXV SENSING BULB AND PIPING

PANEL AREA.

NOTE -

REFER TO OUTDOOR UNIT INSTALLATION

INSTRUCTIONS FOR REFRIGERANT PIPING SIZE

REQUIREMENTS

NOTE -

REFRIGERANT LINE SETS

SHOULD BE ROUTED TO ALLOW

FILTER ACCESSIBILITY.

NOTE -

MCDP* SERIES UNITS USE NITROGEN OR DRY AIR AS A

HOLDING CHARGE. IF THERE IS NO PRESSURE WHEN THE

RUBBER PLUGS ARE REMOVED, CHECK THE COIL FOR LEAKS

BEFORE INSTALLING.

REFER TO INSTRUCTIONS PROVIDED WITH OUTDOOR

UNIT FOR LEAK TESTING, EVACUATING AND CHARGING

PROCEDURES

FLOW REGULATED NITROGEN (AT 1 TO 2 PSIG)

THROUGH THE REFRIGERATION GAUGE SET INTO THE

VALVE STEM PORT CONNECTION ON THE OUTDOOR

UNIT LIQUID LINE SERVICE VALVE AND OUT OF THE

VALVE STEM PORT CONNECTION ON THE SUCTION

SERVICE VALVE.

PLEASE READ IMPORTANT ISSUES CONCERNING BRAZING

OPERATIONS ON PREVIOUS PAGE BEFORE PROCEEDING.

NOTE -

Use silver alloy brazing rods with five or six percent

minimum silver alloy for copper-to-copper brazing, 45

percent alloy for copper-to-brass and copper-to-steel

brazing.

BRAZE

SUCTION

LINE

USE WET RAGS

WHEN BRAZING

SUCTION LINE

Page 8

mrcool.com

Содержание MCDP Series















Результаты поиска

Содержание MCDP Series

Отзывы:

Похожие инструкции для MCDP Series

Бренды по названию

Популярные бренды

MrCool MCDP Series, Руководство по установке

Результаты поиска

Содержание MCDP Series

Отзывы:

Похожие инструкции для MCDP Series

Бренды по названию

Популярные бренды