MR VACUTAP VR Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 268

background image

3 Product description

Maschinenfabrik Reinhausen GmbH 2015

21

4349315/00 EN

VACUTAP® VR®

Product description

This chapter contains an overview of the design and function of the product.

Scope of delivery

The product is packaged with protection against moisture and is usually de-
livered as follows:
▪

Oil compartment with on-load tap-changer head and built-in diverter
switch insert

▪

Selector

▪

Motor-drive unit

▪

Drive shaft with coupling parts and bevel gear

▪

Protective device

▪

Technical files

Please refer to the delivery slip for full details of scope of delivery.

Single-phase on-load tap-changers are also available as an on-load tap-
changer set with a common motor-drive unit.

Note the following information:
▪

Check the shipment for completeness on the basis of the shipping docu-
ments.

▪

Store the parts in a dry place until installation.

▪

The product must remain in its airtight, protective wrapping and may on-
ly be removed immediately before installation

You will find more information in the "Packaging, transport, and storage"
[

36] chapter.

Also refer to

2

Packaging, transport and storage [

On-load tap-changer

Function description

On-load tap-changers are used to adjust the transmission ratio of transform-
ers without interrupting the load flow. Fluctuations in voltage occurring in the
power transmission grid, for example, can therefore be compensated for. For
this purpose, on-load tap-changers are fitted in transformers and connected
to the active part of the transformer.

3

3.1

3.2

3.2.1

«
...
19
20
21
22
23
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: M-system Страницы: 3

Бренд: Balanced Body Страницы: 4

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: ParaBody Страницы: 5

Бренд: Rainin Instrument Страницы: 16

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Lafayette Страницы: 10

Бренд: WARPP Страницы: 28

Бренд: Safco Страницы: 2

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: My-Doc Страницы: 32

Бренд: Spitzer LIGHTING Страницы: 2

Бренд: Cameo Страницы: 56

Бренд: Ametek Страницы: 20

Бренд: VibraPEP Страницы: 2

COLORado Ridge IP

Бренд: Chauvet Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды