MR VACUTAP VR Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 268

background image

4 Packaging, transport and storage

Maschinenfabrik Reinhausen GmbH 2015

36

4349315/00 EN

VACUTAP® VR®

Packaging, transport and storage

Packaging

The products are sometimes supplied with a sealed packaging and some-
times also dried depending on what is required.

A sealed packaging surrounds the packaged goods on all sides with plastic
foil. Products that have also been dried are identified by a yellow label on the
sealed packaging.

The information in the following sections should be applied as appropriate.

Suitability

NOTICE

Property damage due to incorrectly stacked crates!

Stacking the crates incorrectly can lead to damage to the packaged goods!
► Only stack up to 2 equally sized crates on top of one another.

The packaging is suitable for undamaged and fully functional means of
transportation in compliance with local transportation laws and regulations.

The packaged goods are packed in a stable crate. This crate ensures that
the packaged goods are secure when in the intended transportation position
and that none of the parts touch the loading surface of the means of trans-
port or touch the ground after unloading.

The packaged goods are stabilized inside the crate to prevent impermissible
changes in position.

A sealed packaging surrounds the packaged goods on all sides with plastic
foil. The packaged goods are protected from humidity using a desiccant. The
plastic foil is bonded after the drying agent is added.

Markings

The packaging bears a signature with instructions for safe transport and cor-
rect storage. The following symbols apply to the shipment of non-hazardous
goods. Adherence to these symbols is mandatory.

Protect

against mois-

ture

Top

Fragile

Attach lifting

gear here

Center of

mass

Table 6: Shipping pictograms

4

4.1

4.1.1

4.1.2

«
...
34
35
36
37
38
...
»

Содержание VACUTAP VR













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR

Бренд: Landoll Страницы: 34

Бренд: SAMCHULLY Страницы: 48

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: JB-Lighting Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды