MR VACUTAP VR-Ex Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 256

background image

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

216

7545652/00 EN

VACUTAP

®

VR-Ex

In the event of a short-term immobilization time (maximum of 4 weeks) with-
out an oil conservator, it is also sufficient to remove approximately 5 liters of
insulating fluid from the on-load tap-changer oil compartment.

6.2.3 Transport with empty transformer tank

NOTICE

Damage to the on-load tap-changer!

The on-load tap-changer may be subject to oscillating movements during
transformer transportation if the transformer is transported without insulating
fluid and the on-load tap-changer oil compartment is transported with insu-
lating fluid. These oscillating movements can lead to damage to the on-load
tap-changer.

► Completely empty the oil compartment if the transformer is to be trans-

ported without insulating fluid.

► Preserve the oil compartment in the same way as the transformer (for ex-

ample by filling with N2).

6.2.3.1 Emptying oil compartment via pipe connection S

1. De-energize all auxiliary circuits (e.g tap-change supervisory device, pres-

sure relief device, pressure monitoring device).

2. With the stop-cock (slide valve) between oil conservator and oil compart-

ment open, open air-vent valve E1 on the on-load tap-changer head.

3. Discharge the gas from under the on-load tap-changer cover. Ensure suf-

ficient fresh air (e.g. in transformer cells and work tents) when doing so.

4. Once the gas has been discharged and the insulating fluid is flowing out

of the air-vent valve, close the air-vent valve and close the stop-cock be-
tween the oil conservator and oil compartment.

5. Open air-vent valve again and drain off approximately 5–10 liters of insu-

lating fluid via the pipe connection S until the area under the on-load tap-
changer head cover is free of insulating fluid.

6. Loosen 24 screws M10 / wrench size 17 with locking elements on the on-

load tap-changer head cover.

7. Remove on-load tap-changer head cover.

8. Extract insulating fluid via pipe connection S.

9. Open stop-cock between oil conservator and oil compartment.

ð

Insulating fluid flows out of the oil conservator into the oil compartment.

10. Extract insulating fluid via pipe connection S.

11. Place on-load tap-changer head cover on the on-load tap-changer head.

12. Screw down on-load tap-changer head cover using 24 screws M10 /

wrench size 17 and locking elements (tightening torque 34 Nm).

«
...
214
215
216
217
218
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренд: ABB Страницы: 2

MTC-8000 Series

Бренд: Vecow Страницы: 55

Бренд: Climax Страницы: 126

Бренд: Dodge Страницы: 2

Бренд: California Air Tools Страницы: 7

Бренд: Weller Страницы: 91

Бренд: M-system Страницы: 8

Бренд: Hauff-Technik Страницы: 2

Evaluation kit 60 V

Бренд: TDK Страницы: 28

LUMASTAR EPL-100

Бренд: Jerguson Страницы: 3

eBOX671-521-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Graco Страницы: 82

Бренд: Smart Dedicated Design Страницы: 6

GQM22M5C2H1R5BB01 Series

Бренд: Murata Страницы: 25

ebro EBI DA Set

Бренд: Xylem Страницы: 8

Climexel 9200200

Бренд: Procopi Страницы: 48

Бренд: Magnaflux Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды