manualshive.com logo in svg

MR TAPCON 230 VC, Руководство по эксплуатации, Страница: 8 / 32

Поделиться
Скачать
MR TAPCON 230 VC Скачать руководство пользователя страница 8

8

251/02 en

2   Technical Data

Protective housing

Steel-plate housing with inspection window for flush or projected panel mounting
W x H x D: 216 x 326 x 137mm

Degree of protection provided by enclosure: IP 44 according to IEC 60529

Weight: approx. 5.4 kgs

Temperature limits

Admissible ambient temperature for operation:  -10 °C ... + 70 °C
Admissible ambient temperature for storage and transport: -25 °C ... +80 °C

Tests

IEC 255-5

Dielectric tests performed at 2.5 kV/1 min operating frequency and 5 kV, 1.2|50 

μ

s impulse voltage

IEC 61000-4-2

Interference immunity tests (EMC): electrostatic discharge 4 kV / 8 kV

IEC 61000-4-3

Interference immunity tests (EMC): electromagnetic fields 10 V/m
80-1000 MHz

IEC 61000-4-4

Interference immunity tests (EMC): burst 1MHz, 4 kV

IEC 61000-4-5

Interference immunity, surge 2 kV

IEC 61000-4-6

HF interference immunity of leads: 10V, 150 kHz – 80 MHz

EN 61000-6-2

Immunity for industrial environments

EN 61000-6-4

Emission standards for industrial environments

VDE 0435

Short-time current and continuous rating of the current transformer inputs,

100 x In/1s and 2 x In/continuously

VDE 0100

Provisions governing the erection of electrical power installations featuring rated system voltages
up to 1,000 V
Grounding conductors, protective conductors, equipotential bonding conductors,
arrangement of operating elements

I

EC 61010 / VDE 0411

Safety requirements for electrical equipment for measurement, control, regulation and
laboratory use

VDE 0110

Provisions governing the rating of clearance in air and creepage distances in electrical equipment

IEC 60529

Determination of the degree of protection provided by enclosures: „Shock-hazard protection,
protection against ingress of solid foreign bodies and protection against the ingress of water for
electrical equipment“ Level IP00

IEC 60068

Basic environmental test procedures

IEC 60068-2-1

Cold test for heat-dissipating specimens, with slow temperature change rate -10°C / 20 hours

IEC 60068-2-2

Dry-heat test for heat-dissipating specimens, with slow temperature change rate
+70 °C / 16 hous

IEC 60068-2-3

Humid heat, constant
+40 °C / 93 % / 56 days

IEC 60068-2-30

Humid heat, cyclical (12 + 12 hours)
+ 55 °C / 93 % and + 25 °C / 95 % / 6 cycles

IEC 60068-2-31

Drops and topple, unpacked, 100 mm height

IEC 60068-2-32

Free fall, unpacked, 250 mm height

IEC 61000-4-8

Power frequency magnetic field immunity test

IEC 61000-4-11

Voltage dips, short interruptions and voltage variations immunity tests

Содержание TAPCON 230 VC

































Отзывы:

Нет отзывов