manualshive.com logo in svg

MR TAPCON 230 VC, Руководство по эксплуатации, Страница: 2 / 32

Поделиться
Скачать
MR TAPCON 230 VC Скачать руководство пользователя страница 2

2

251/02 en

Contents

Contents

1

Genera

l

..............................................................................................................................................................................................................

4

1.1

Safety instructions ............................................................................................................................................................................

4

1.2

Specified application .......................................................................................................................................................................

4

1.3

Design and performance features of the TAPCON® 230 VC ................................................................................................

5

2

Technical Data

................................................................................................................................................................................................

6

3

Operation

.........................................................................................................................................................................................................

9

3.1

Input and output of data; functions ..........................................................................................................................................

9

3.2

Description of the front panel ......................................................................................................................................................

9

3.2.1

Display ..................................................................................................................................................................................... 10

3.2.2

Local/remote switch ........................................................................................................................................................... 11

4

Parametering

.................................................................................................................................................................................................. 11

4.1

Normset setting ................................................................................................................................................................................. 11

4.2

Setting the desired voltage level 1 .............................................................................................................................................. 12

4.3

Setting the bandwidth .................................................................................................................................................................... 12

4.4

Setting the delay time T1 or T2 (DELAY 1/DELAY 2) and pulse duration (option) ........................................................ 12

4.5

Setting the overvoltage detection (U>) with automatic return control ......................................................................... 13

4.6

Setting the undervoltage blocking (U<) .................................................................................................................................... 13

4.7

Setting the overcurrent blocking (I>) ......................................................................................................................................... 13

4.8

Measuring transformers (VT, CT configuration) ....................................................................................................................... 15

4.9

Setting the desired voltage levels DVL2 and DVL3 ................................................................................................................. 15

4.10

Line compensation ............................................................................................................................................................................ 15

4.10.1 Line drop compensation (LDC) ........................................................................................................................................ 15

4.10.2 Z-Compensation .................................................................................................................................................................. 16

4.11

Analog remote position indication (option) ............................................................................................................................. 16

4.12

Voltage regulator identification ................................................................................................................................................... 17

4.13

Setting the unit to V or kV ............................................................................................................................................................. 17

4.14

Selection of the display in the 4

th

 line of the display ........................................................................................................... 17

4.15

Language selection ........................................................................................................................................................................... 17

Содержание TAPCON 230 VC

































Отзывы:

Нет отзывов