manualshive.com logo in svg

MR ECOTAP VPD I, Руководство по эксплуатации

Поделиться
Скачать
MR ECOTAP VPD I Скачать руководство пользователя страница 49

6 Commissioning

Maschinenfabrik Reinhausen GmbH 2019

49

6107891/02 EN

ECOTAP

®

 VPD

®

6 Commissioning

This chapter describes how to commission the device. Commissioning is
broken down into the following sections:

▪ Commissioning at the transformer manufacturer's site

▪ Transporting transformer to the operating site

▪ Commissioning at the operating site

6.1 Commissioning the on-load tap-changer at the transformer

manufacturer's site

 WARNING

Flying parts and spraying of hot oil resulting from on-load tap-
changer overload!

The on-load tap-changer can switch currents of up to twice the rated
through-current. Higher currents occur when activating transformers (inrush
current impulse) or in the event of short-circuits, for example. Higher volt-
ages may occur due to transformer overexcitation following load shedding,
for example.

Danger of death or severe injury due to flying parts and spraying of hot oil!

► Ensure that the on-load tap-changer is not overloaded.

► Prevent on-load tap-change operations if higher currents arise.

► Ensure that the rated step voltage is not exceeded. The rated step volt-

age may be briefly exceeded by up to 10% as long as the rated through-
current is not exceeded.

► Ensure that the temperature limit values stated in the technical data are

not exceeded.

NOTICE

Damage to on-load tap-changer resulting from switching with-
out oil!

Performing too many operations without a complete transformer oil fill will
damage the on-load tap-changer!

► Do not perform more than 100 tap-change operations without a full oil fill.

► Only use emergency drive shaft to rectify faults [

►

Section 8, Page 58]

and never operate with a drill.

Before starting to test the transformer, take the following steps, which are
described in detail in the operating instructions for the ECOTAP® VPD® mo-
tor-drive unit:

1. Mount and connect motor-drive unit and control unit.

2. Commission motor-drive unit and control unit.

3. Carry out automatic adjustment and trial tap-change operations.

ð

You can then start the transformer tests. Observe the description below.

Содержание ECOTAP VPD I



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды