MQ Power DCA40SSKU4F2 Скачать руководство пользователя страница 44

Страница: 44 / 52

PAGE 44 — DCA40SSKU4F2 60 HZ GENERATOR • OPERATION MANUAL — REV. #0 (07/20/17)

E N G I N E B L O C K H E AT I N G E L E M E N T

ANDINTERNAL BATTERY CHARGER 120 VAC

INPUT RECEPTACLES (OPTIONAL)

This generator can be equipped as an

option

with a

engine block heating element

and an

internal battery

charger

. They are provided with electric cords to connect

to a commercial power source.
The engine block heating element and internal battery

charger both require 120 VAC in order to operate. A

receptacle (Figure 65 )has been provided on the output

terminal panel to allow commercial power to be applied.
These units will

ONLY

function when commercial power

has been supplied to them. When using extension cords,

refer to Table 6 for the correct size and length.
The battery charger should always be connected to a

commercial power source to ensure that the battery does

not get discharged.
When using the generator in

hot

climates there is no

need to apply power to jacket water heater. However, if the

generator will be used in

cold

climates, it is best to apply

power to the jacket water heater at all times.
If the generator will be used daily, the battery should

normally not require charging. If the generator will be idle

(not used) for long periods of time, apply power to the

battery charger receptacle via commercial power using a

power cord of adequate size.

GENERATOR STORAGE

For long term storage of the generator the following is

recommended:

Drain the fuel tank completely. Treat with a fuel stabilizer

if necessary.

Completely drain the oil from the crankcase and refill if

necessary with fresh oil.

Clean the entire generator, internal and external.

Cover the generating set and store in a clean, dry place.

Disconnect the battery.

Make sure engine coolant is at proper level.

If generator is mounted on a trailer, jack trailer up and

place on blocks so tires do not touch the ground or block

and completely remove the tires.

NOTICE

To ensure adequate starting capability, always have

power applied to the generator's internal battery

charger.

MAINTENANCE

Figure 65. Battery Charger and Jacket Water

Heater (Option)

BATTERY CHARGER

BATTERY CHARGER/

ENGINE BLOCK

HEATING ELEMENT

120 VAC INPUT

RECEPTACLE

OUTPUT TERMINAL

PANEL ASSEMBLY

ENGINE BLOCK

HEATING ELEMENT

TO STARTER “B”

TERMINAL

RED 16 AWG.

TO CHASSIS

GROUND

GREEN 16 AWG.

Содержание DCA40SSKU4F2





















































Результаты поиска

Содержание DCA40SSKU4F2

Отзывы:

Похожие инструкции для DCA40SSKU4F2

Бренды по названию

Популярные бренды

MQ Power DCA40SSKU4F2, Руководство по эксплуатации

Результаты поиска

Содержание DCA40SSKU4F2

Отзывы:

Похожие инструкции для DCA40SSKU4F2

Бренды по названию

Популярные бренды