MQ Power DCA40SSKU4F2 Скачать руководство пользователя страница 18

Страница: 18 / 52

PAGE 18 — DCA40SSKU4F2 60 HZ GENERATOR • OPERATION MANUAL — REV. #0 (07/20/17)

Figure 4. Engine Control Panel

DECREASE

INCREASE

V-W

U-V

OFF

W-U

Low Oil Pressre

High temp.

Over Crank

Over Speed

Engine Started

ECU

Intergrated Gauge Control

The definitions below and on the preceeding page describe

the controls and functions of the Engine Control Panel

(Figure 4).
1.

Engine Warning LEDs

— There are six engine

warning lamps, they are defined as follows:
a.

Engine Shutdown

— Indicates that the engine

has shutdown due to an engine failure LED will

turn on.

Engine Pre Alarm LED

— Indicates that an engine

failure has occured. LED will turn on or blink.

Battery Charge Alarm LED

— This LED is

when the output voltage of the alternator drops

below a set value. If this lamp is ON during normal

operation, the emergency shutdown system will

immediately stop the engine.

Fuel Filter Water Level LED

— This LED is

when the water level in the fuel filter is extradinary

high.

Fuel Leak Detected Lamp LED

— This LED is

when thefluid in the containment is higher than

allowable level.

Pre-Heat LED

— The pre-heat LED will be

during the pre-heating cycle (cold weather

conditions). When the pre-heat cycle is completed

the LED will turn

OFF

and the engine can be

started.

ENGINE CONTROL PANEL

Содержание DCA40SSKU4F2





















































Результаты поиска

Содержание DCA40SSKU4F2

Отзывы:

Похожие инструкции для DCA40SSKU4F2

Бренды по названию

Популярные бренды

MQ Power DCA40SSKU4F2, Руководство по эксплуатации

Результаты поиска

Содержание DCA40SSKU4F2

Отзывы:

Похожие инструкции для DCA40SSKU4F2

Бренды по названию

Популярные бренды