background image

 

- 10 -

Multi mode: 

 

100BaseFX 

0 to 5 km, 1300 nm (50/125

μ

m, 800MHz*km) 

0 to 4 m, 1300 nm (62.5/125

μ

m, 500MHz*km) 

Single mode: 

 

100BaseFX 

0 to 40 km, 1310 nm (9/125

μ

m, 3.5 PS/(nm*km)) 

The concept behind the LC port and cable is quite straightforward. Suppose 
you are connecting devices I and II. Unlike electrical signals, optical signals do 
not require a circuit in order to transmit data. Consequently, one of the optical 
lines is used to transmit data from device I to device II, and the other optical 
line is used to transmit data from device II to device I, for full-duplex 
transmission. 

Remember to connect the Tx (transmit) port of device I to the Rx (receive) port 
of device II, and the Rx (receive) port of device I to the Tx (transmit) port of 
device II. If you make your own cable, we suggest labeling the two sides of the 
same line with the same letter (A-to-A and B-to-B, as shown below, or 
A1-to-A2 and B1-to-B2). 

 

LC-Port Pinouts

 

LC-Port to LC-Port Cable Wiring

 

Tx

Rx

 

A

B

Cable Wiring

 

 

                       A

 

 

                       B

A

B

 

 

 

ATTENTION 

This is a Class 1 Laser/LED product. To avoid causing serious 
damage to your eyes, do not stare directly into the Laser Beam. 

Turbo Ring DIP Switch Settings 

EDS-G509 series are plug-and-play managed redundant Ethernet switches. The 
proprietary Turbo Ring protocol was developed by Moxa to provide better 
network reliability and faster recovery time. Moxa Turbo Ring’s recovery time 
is less than 300 ms (

Turbo Ring

) or 20 ms (

Turbo Ring V2

) —compared to a 

3- to 5-minute recovery time for commercial switches—decreasing the possible 
loss caused by network failures in an industrial setting. 

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of 
EDS-G509 that can help setup the Turbo Ring easily within seconds. If you do 
not want to use a hardware DIP switch to setup the Turbo Ring, you can use a 
web browser, telnet, or console to disable this function. 

NOTE

 

Please refer to the 

Turbo Ring DIP Switch

 section and 

Using 

Communication Redundancy

 section in the User’s Manual for 

more detail information about the settings and usage of 

Turbo Ring

 

and 

Turbo Ring V2

 

Содержание EtherDevice EDS-G509
















Отзывы: