Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя

Страница: 77 / 97

EDS-518A Series User’s Manual

Featured Functions

3-62

Using the MAC Address Table

This section explains the information provided by EDS-518A’s MAC address table.

The MAC Address table can be configured to display the following EDS-518A MAC address
groups.

ALL

Select this item to show all EDS-518A MAC addresses

ALL Learned

Select this item to show all EDS-518A Learned MAC addresses

ALL Static Lock

Select this item to show all EDS-518A Static Lock MAC addresses

ALL Static

Select this item to show all EDS-518A Static/Static Lock /Static
Multicast MAC addresses

ALL Static
Multicast

Select this item to show all EDS-518A Static Multicast MAC
addresses

Port x

Select this item to show all MAC addresses of dedicated ports

The table will display the following information:

MAC

This field shows the MAC address

Type

This field shows the type of this MAC address

Port

This field shows the port that this MAC address belongs to

Using Event Log

Содержание EtherDevice EDS-518A Series


































































































Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды

Moxa Technologies EtherDevice EDS-518A Series, Руководство пользователя

Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды